macb0: ethernet@f0028000 {
                                phy-mode = "rgmii-txid";
                                #address-cells = <1>;
                                #size-cells = <0>;
                                status = "okay";

                                fixed-link {
                                        speed = <1000>;
                                        full-duplex;
                                        pause;
                                };
                        };


i2c0: i2c@f0014000 {
                                pinctrl-0 = <&pinctrl_i2c0_pu>;
                                status = "okay";

                                i2c_ksz9477: ksz9477@5f {
                                        compatible = "microchip,ksz9477";
                                        reg = <0x5f>;

                                        interrupt-parent = <&pioB>;
                                        interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
                                        status = "okay";
                                        ports {
                                                #address-cells = <1>;
                                                #size-cells = <0>;
                                                port@0 {
                                                        reg = <0>;
                                                        label = "lan1";
                                                };
                                                port@1 {
                                                        reg = <1>;
                                                        label = "lan2";
                                                };
                                                port@2 {
                                                        reg = <2>;
                                                        label = "lan3";
                                                };
                                                port@3 {
                                                        reg = <3>;
                                                        label = "lan4";
                                                };
                                                port@4 {
                                                        reg = <4>;
                                                        label = "lan5";
                                                };
                                                port@5 {
                                                        reg = <5>;
                                                        label = "cpu";
                                                        ethernet = <&macb0>;
                                                        phy-mode = "rgmii-txid";
                                                        fixed-link {
                                                                speed = <1000>;
                                                                full-duplex;
                                                                pause;
                                                        };
                                                };
                                                port@6 {
                                                        reg = <6>;
                                                        label = "lan6";
                                                        mode = <1>;
                                                };
                                        };
                                };
                        };






spi1: spi@f8008000 {
                                cs-gpios = <&pioC 25 GPIO_ACTIVE_LOW>, <0>, <0>, <&pioC 28 GPIO_ACTIVE_LOW>;
                                status = "okay";
                                id = <1>;

                                ksz9477: ksz9477@0 {
                                        compatible = "microchip,ksz9477";
                                        reg = <0>;

                                        /* Bus clock is 132 MHz. */
                                        spi-max-frequency = <44000000>;
                                        spi-cpha;
                                        spi-cpol;
                                        interrupt-parent = <&pioB>;
                                        interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
                                        status = "okay";
                                        ports {
                                                #address-cells = <1>;
                                                #size-cells = <0>;
                                                port@0 {
                                                        reg = <0>;
                                                        label = "lan1";
                                                };
                                                port@1 {
                                                        reg = <1>;
                                                        label = "lan2";
                                                };
                                                port@2 {
                                                        reg = <2>;
                                                        label = "lan3";
                                                };
                                                port@3 {
                                                        reg = <3>;
                                                        label = "lan4";
                                                };
                                                port@4 {
                                                        reg = <4>;
                                                        label = "lan5";
                                                };
                                                port@5 {
                                                        reg = <5>;
                                                        label = "cpu";
                                                        ethernet = <&macb0>;
                                                        phy-mode = "rgmii-txid";
                                                        fixed-link {
                                                                speed = <1000>;
                                                                full-duplex;
                                                                pause;
                                                        };
                                                };
                                                port@6 {
                                                        reg = <6>;
                                                        label = "lan6";
                                                };
                                        };
    				 };
                        };