U-Boot 2014.10 (May 01 2016 - 08:22:23) CPU : Altera SOCFPGA Arria 10 Platform BOARD : Altera SOCFPGA Arria 10 Dev Kit DRAM: WARNING: Caches not enabled SOCFPGA DWMMC: 0 FPGA: writing socfpga.rbf FPGA: Success.DDRCAL: Success INFO : Skip relocation as SDRAM is non secure memory Reserving 2048 Bytes for IRQ stack at: ffe2db10 DRAM : 1 GiB WARNING: Caches not enabled MMC: *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: SOCFPGA Arria10 Dev Kit Net: dwmac.ff800000 Error: dwmac.ff800000 address not set. Hit any key to stop autoboot: 5  4  3  2  1  0 Early IO release is not enabled!! ** Unable to read file u-boot.scr ** Optional boot script not found. Continuing to boot normally 3464136 bytes read in 85 ms (38.9 MiB/s) 23812 bytes read in 4 ms (5.7 MiB/s) FPGA BRIDGES: enable Kernel image @ 0x008000 [ 0x000000 - 0x34dbc8 ] ## Flattened Device Tree blob at 00000100 Booting using the fdt blob at 0x000100 Loading Device Tree to 01ff7000, end 01fffd03 ... OK Starting kernel ... Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Linux version 3.10.31-ltsi-02998-g28bac3e (esv@pg-iccf0334) (gcc version 4.9.3 20141031 (prerelease) (Linaro GCC 4.9-2014.11) ) #1 SMP Sun May 1 08:53:06 MYT 2016 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Altera SOCFPGA, model: Altera SOCFPGA Arria 10 Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 8 pages/cpu @80f5c000 s11200 r8192 d13376 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1024MB = 1024MB total Memory: 1031964k/1031964k available, 16612k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc0800000 - 0xff000000 (1000 MB) lowmem : 0x80000000 - 0xc0000000 (1024 MB) modules : 0x7f000000 - 0x80000000 ( 16 MB) .text : 0x80008000 - 0x8067b084 (6605 kB) .init : 0x8067c000 - 0x806cfbc0 ( 335 kB) .data : 0x806d0000 - 0x8070c990 ( 243 kB) .bss : 0x8070c990 - 0x8074c334 ( 255 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 SOCFPGA: Unable to find sdr-ctl sched_clock: 32 bits at 50MHz, resolution 20ns, wraps every 85899ms Console: colour dummy device 80x30 Calibrating delay loop... 2387.14 BogoMIPS (lpj=11935744) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok ftrace: allocating 17773 entries in 53 pages CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x804c7518 - 0x804c7570 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (4780.85 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized NET: Registered protocol family 16 fpga bridge driver DMA: preallocated 256 KiB pool for atomic coherent allocations L310 cache controller enabled l2x0: 8 ways, CACHE_ID 0x410030c9, AUX_CTRL 0x72560001, Cache size: 524288 B ERROR: could not get clock /sopc@0/dma@0xffda1000:apb_pclk(0) syscon ffd06000.sysmgr: regmap [mem 0xffd06000-0xffd063ff] registered syscon ffd05000.rstmgr: regmap [mem 0xffd05000-0xffd050ff] registered hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. bio: create slab at 0 FPGA Mangager framework driver SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb lcd-comm 0-0028: LCD driver initialized pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Switching to clocksource timer NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP: reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available arm-pmu arm-pmu: PMU:CTI successfully enabled for 2 cores NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered NTFS driver 2.1.30 [Flags: R/W]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 2015 io scheduler noop registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled ffc02100.serial: ttyS0 at MMIO 0xffc02100 (irq = 143) is a 16550A console [ttyS0] enabled socfpga_a10_fpga_manager ffd03000.fpgamgr: fpga manager [SoCFPGA Arria10 FPGA Manager] registered as minor 0 brd: module loaded at24 0-0051: 4096 byte 24c32 EEPROM, writable, 32 bytes/write dw_spi_mmio ffda5000.spi: master is unqueued, this is deprecated CAN device driver interface stmmac - user ID: 0x10, Synopsys ID: 0x37 Ring mode enabled DMA HW capability register supported Enhanced/Alternate descriptors Enabled extended descriptors RX Checksum Offload Engine supported (type 2) TX Checksum insertion supported Enable RX Mitigation via HW Watchdog Timer libphy: stmmac: probed eth0: PHY ID 00221622 at 7 IRQ POLL (stmmac-0:07) active dwc2 ffb00000.usb: unable to find phy dwc2 ffb00000.usb: EPs:15 dwc2 ffb00000.usb: dedicated fifos dwc2 ffb00000.usb: 2560 invalid for host_rx_fifo_size. Check HW configuration. dwc2 ffb00000.usb: DWC OTG Controller dwc2 ffb00000.usb: new USB bus registered, assigned bus number 1 dwc2 ffb00000.usb: irq 127, io mem 0x00000000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: DWC OTG Controller usb usb1: Manufacturer: Linux 3.10.31-ltsi-02998-g28bac3e dwc2_hsotg usb usb1: SerialNumber: ffb00000.usb hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage mousedev: PS/2 mouse device common for all mice rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0 i2c /dev entries driver Synopsys Designware Multimedia Card Interface Driver dwmmc_socfpga ff808000.flash: Using internal DMA controller. dwmmc_socfpga ff808000.flash: Version ID is 270a dwmmc_socfpga ff808000.flash: DW MMC controller at irq 130, 32 bit host data width, 1024 deep fifo mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) dwmmc_socfpga ff808000.flash: 1 slots initialized platform leds.2: Driver leds-gpio requests probe deferral ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver oprofile: using arm/armv7-ca9 TCP: cubic registered NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 can: controller area network core (rev 20120528 abi 9) NET: Registered protocol family 29 can: raw protocol (rev 20120528) can: broadcast manager protocol (rev 20120528 t) can: netlink gateway (rev 20130117) max_hops=1 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 ThumbEE CPU extension supported. Registering SWP/SWPB emulation handler platform leds.2: Driver leds-gpio requests probe deferral Waiting for root device /dev/mmcblk0p2... mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD16G 14.5 GiB mmcblk0: p1 p2 p3 platform leds.2: Driver leds-gpio requests probe deferral kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): using internal journal EXT3-fs (mmcblk0p2): recovery complete EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) on device 179:2. devtmpfs: mounted Freeing unused kernel memory: 332K (8067c000 - 806cf000) Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b CPU: 1 PID: 1 Comm: init Not tainted 3.10.31-ltsi-02998-g28bac3e #1 [<80016538>] (unwind_backtrace+0x0/0xf8) from [<80012e24>] (show_stack+0x20/0x24) [<80012e24>] (show_stack+0x20/0x24) from [<804c39e4>] (dump_stack+0x24/0x28) [<804c39e4>] (dump_stack+0x24/0x28) from [<804c1890>] (panic+0xac/0x1f8) [<804c1890>] (panic+0xac/0x1f8) from [<80028d34>] (complete_and_exit+0x0/0x2c) [<80028d34>] (complete_and_exit+0x0/0x2c) from [<80029c54>] (do_group_exit+0x5c/0xdc) [<80029c54>] (do_group_exit+0x5c/0xdc) from [<80037880>] (get_signal_to_deliver+0x298/0x660) [<80037880>] (get_signal_to_deliver+0x298/0x660) from [<800122e4>] (do_signal+0x114/0x464) [<800122e4>] (do_signal+0x114/0x464) from [<800127bc>] (do_work_pending+0x74/0xb4) [<800127bc>] (do_work_pending+0x74/0xb4) from [<8000e6c0>] (work_pending+0xc/0x20) CPU0: stopping CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.31-ltsi-02998-g28bac3e #1 [<80016538>] (unwind_backtrace+0x0/0xf8) from [<80012e24>] (show_stack+0x20/0x24) [<80012e24>] (show_stack+0x20/0x24) from [<804c39e4>] (dump_stack+0x24/0x28) [<804c39e4>] (dump_stack+0x24/0x28) from [<800144dc>] (handle_IPI+0x120/0x13c) [<800144dc>] (handle_IPI+0x120/0x13c) from [<80008590>] (gic_handle_irq+0x68/0x6c) [<80008590>] (gic_handle_irq+0x68/0x6c) from [<8000e280>] (__irq_svc+0x40/0x50) Exception stack(0x806d1f30 to 0x806d1f78) 1f20: 80f5c7f8 00000000 00016ac4 00000000 1f40: 806d0000 806d0008 806d0000 8070b410 806d83e8 806d843c 00000000 806d1f84 1f60: 806d1f88 806d1f78 8000fa7c 8000fa80 60000113 ffffffff [<8000e280>] (__irq_svc+0x40/0x50) from [<8000fa80>] (arch_cpu_idle+0x3c/0x40) [<8000fa80>] (arch_cpu_idle+0x3c/0x40) from [<80060b8c>] (cpu_startup_entry+0x148/0x218) [<80060b8c>] (cpu_startup_entry+0x148/0x218) from [<804bd28c>] (rest_init+0x84/0x88) [<804bd28c>] (rest_init+0x84/0x88) from [<8067cab4>] (start_kernel+0x2b4/0x2c0)