[root@localhost home]# /opt/MegaRAID/storcli/storcli /c0 show all Generating detailed summary of the adapter, it may take a while to complete. Controller = 0 Status = Success Description = None Basics : ====== Controller = 0 Model = Intel(R) Integrated RAID Module RMS3CC080 Serial Number = SV43930311 Current Controller Date/Time = 03/30/2020, 07:38:48 Current System Date/time = 03/30/2020, 07:38:48 SAS Address = 500605b0099b93f0 PCI Address = 00:01:00:00 Mfg Date = 10/19/14 Rework Date = 00/00/00 Revision No = 09C Version : ======= Firmware Package Build = 24.21.0-0012 Firmware Version = 4.680.00-8249 CPLD Version = 26668-01A Bios Version = 6.36.00.0_4.19.08.00_0x06180200 HII Version = 03.25.05.00 Ctrl-R Version = 5.19-0600 Preboot CLI Version = 01.07-05:#%0000 NVDATA Version = 3.1705.00-0002 Boot Block Version = 3.07.00.00-0003 Driver Name = megaraid_sas Driver Version = 06.700.06.00-rh1 Bus : === Vendor Id = 0x1000 Device Id = 0x5D SubVendor Id = 0x8086 SubDevice Id = 0x351E Host Interface = PCI-E Device Interface = SAS-12G Bus Number = 1 Device Number = 0 Function Number = 0 Pending Images in Flash : ======================= Image name = No pending images Status : ====== Controller Status = Optimal Memory Correctable Errors = 0 Memory Uncorrectable Errors = 0 ECC Bucket Count = 0 Any Offline VD Cache Preserved = No BBU Status = 0 Support PD Firmware Download = No Lock Key Assigned = No Failed to get lock key on bootup = No Lock key has not been backed up = No Bios was not detected during boot = No Controller must be rebooted to complete security operation = No A rollback operation is in progress = No At least one PFK exists in NVRAM = Yes SSC Policy is WB = No Controller has booted into safe mode = No Current Personality = RAID-Mode Supported Adapter Operations : ============================ Rebuild Rate = Yes CC Rate = Yes BGI Rate = Yes Reconstruct Rate = Yes Patrol Read Rate = Yes Alarm Control = Yes Cluster Support = No BBU = Yes Spanning = Yes Dedicated Hot Spare = Yes Revertible Hot Spares = Yes Foreign Config Import = Yes Self Diagnostic = Yes Allow Mixed Redundancy on Array = No Global Hot Spares = Yes Deny SCSI Passthrough = No Deny SMP Passthrough = No Deny STP Passthrough = No Support more than 8 Phys = Yes FW and Event Time in GMT = No Support Enhanced Foreign Import = Yes Support Enclosure Enumeration = Yes Support Allowed Operations = Yes Abort CC on Error = Yes Support Multipath = Yes Support Odd & Even Drive count in RAID1E = No Support Security = No Support Config Page Model = Yes Support the OCE without adding drives = Yes Support EKM = No Snapshot Enabled = No Support PFK = Yes Support PI = Yes Support LDPI Type1 = No Support LDPI Type2 = No Support LDPI Type3 = No Support Ld BBM Info = No Support Shield State = Yes Block SSD Write Disk Cache Change = No Support Suspend Resume BG ops = Yes Support Emergency Spares = No Support Set Link Speed = Yes Support Boot Time PFK Change = No Support JBOD = Yes Disable Online PFK Change = No Support Perf Tuning = Yes Support SSD PatrolRead = Yes Real Time Scheduler = Yes Support Reset Now = Yes Support Emulated Drives = Yes Headless Mode = Yes Dedicated HotSpares Limited = No Point In Time Progress = Yes Extended LD = Yes Boot Volume Supported = No Support Uneven span = No Support Config Auto Balance = No Support Maintenance Mode = No Support Diagnostic results = Yes Support Ext Enclosure = Yes Support Sesmonitoring = Yes Support SecurityonJBOD = Yes Support ForceFlash = Yes Support DisableImmediateIO = Yes Support LargeIOSupport = Yes Support DrvActivityLEDSetting = Yes Support FlushWriteVerify = Yes Support CPLDUpdate = Yes Support ForceTo512e = Yes Support discardCacheDuringLDDelete = Yes Support JBOD Write cache = No Support Large QD Support = No Support SRIOV Options = No Supported PD Operations : ======================= Force Online = Yes Force Offline = Yes Force Rebuild = Yes Deny Force Failed = No Deny Force Good/Bad = No Deny Missing Replace = No Deny Clear = No Deny Locate = No Support Power State = Yes Set Power State For Cfg = No Support T10 Power State = No Support Temperature = Yes NCQ = Yes Support Max Rate SATA = No Support Degraded Media = No Support Parallel FW Update = Yes Support Drive Crypto Erase = Yes Supported VD Operations : ======================= Read Policy = Yes Write Policy = Yes IO Policy = Yes Access Policy = Yes Disk Cache Policy = Yes Reconstruction = Yes Deny Locate = No Deny CC = No Allow Ctrl Encryption = No Enable LDBBM = No Support FastPath = Yes Performance Metrics = Yes Power Savings = No Support Powersave Max With Cache = No Support Breakmirror = Yes Support SSC WriteBack = No Support SSC Association = No Support VD Hide = Yes Support VD Cachebypass = Yes Support VD discardCacheDuringLDDelete = Yes Advanced Software Option : ======================== ---------------------------------------- Adv S/W Opt Time Remaining Mode ---------------------------------------- MegaRAID FastPath Unlimited - MegaRAID RAID6 Unlimited - MegaRAID RAID5 Unlimited - ---------------------------------------- Safe ID = 5FUD2Q7S6DKP1X342ILMA94W8RV85Q3XUA34X52Z HwCfg : ===== ChipRevision = C0 BatteryFRU = N/A Front End Port Count = 0 Backend Port Count = 8 BBU = Present Alarm = On Serial Debugger = Present NVRAM Size = 32KB Flash Size = 16MB On Board Memory Size = 1024MB CacheVault Flash Size = 4.0 GB TPM = Absent Upgrade Key = Absent On Board Expander = Absent Temperature Sensor for ROC = Present Temperature Sensor for Controller = Absent Upgradable CPLD = Present Current Size of CacheCade (GB) = 0 Current Size of FW Cache (MB) = 927 ROC temperature(Degree Celsius) = 67 Policies : ======== Policies Table : ============== ------------------------------------------------ Policy Current Default ------------------------------------------------ Predictive Fail Poll Interval 300 sec Interrupt Throttle Active Count 16 Interrupt Throttle Completion 50 us Rebuild Rate 30 % 30% PR Rate 30 % 30% BGI Rate 30 % 30% Check Consistency Rate 30 % 30% Reconstruction Rate 30 % 30% Cache Flush Interval 4s ------------------------------------------------ Flush Time(Default) = 4s Drive Coercion Mode = 1GB Auto Rebuild = On Battery Warning = On ECC Bucket Size = 15 ECC Bucket Leak Rate (hrs) = 24 Restore HotSpare on Insertion = On Expose Enclosure Devices = Off Maintain PD Fail History = On Reorder Host Requests = On Auto detect BackPlane = SGPIO/i2c SEP Load Balance Mode = Auto Security Key Assigned = Off Disable Online Controller Reset = Off Use drive activity for locate = Off Boot : ==== BIOS Enumerate VDs = 1 Stop BIOS on Error = On Delay during POST = 0 Spin Down Mode = None Enable Ctrl-R = Yes Enable Web BIOS = No Enable PreBoot CLI = No Enable BIOS = Yes Max Drives to Spinup at One Time = 1 Maximum number of direct attached drives to spin up in 1 min = 60 Delay Among Spinup Groups (sec) = 1 Allow Boot with Preserved Cache = Off High Availability : ================= Topology Type = None Cluster Permitted = No Cluster Active = No Defaults : ======== Phy Polarity = 0 Phy PolaritySplit = 0 Strip Size = 256 KB Write Policy = WB Read Policy = RA Cache When BBU Bad = Off Cached IO = Off VD PowerSave Policy = Controller Defined Default spin down time (mins) = 30 Coercion Mode = 1 GB ZCR Config = Unknown Max Chained Enclosures = 16 Direct PD Mapping = No Restore Hot Spare on Insertion = Yes Expose Enclosure Devices = No Maintain PD Fail History = Yes Zero Based Enclosure Enumeration = No Disable Puncturing = No EnableLDBBM = No DisableHII = No Un-Certified Hard Disk Drives = Allow SMART Mode = Mode 6 Enable LED Header = Yes LED Show Drive Activity = Yes Dirty LED Shows Drive Activity = No EnableCrashDump = Yes Disable Online Controller Reset = No Treat Single span R1E as R10 = No Power Saving option = Enabled TTY Log In Flash = Yes Auto Enhanced Import = No BreakMirror RAID Support = Yes Disable Join Mirror = Yes Enable Shield State = Yes Time taken to detect CME = 60 sec Capabilities : ============ Supported Drives = SAS, SATA Boot Volume Supported = NO RAID Level Supported = RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Enable JBOD = No Mix in Enclosure = Allowed Mix of SAS/SATA of HDD type in VD = Allowed Mix of SAS/SATA of SSD type in VD = Not Allowed Mix of SSD/HDD in VD = Not Allowed SAS Disable = No Max Arms Per VD = 32 Max Spans Per VD = 8 Max Arrays = 128 Max VD per array = 16 Max Number of VDs = 64 Max Parallel Commands = 928 Max SGE Count = 60 Max Data Transfer Size = 8192 sectors Max Strips PerIO = 128 Max Configurable CacheCade Size(GB) = 0 Max Transportable DGs = 0 Min Strip Size = 64 KB Max Strip Size = 1.0 MB Scheduled Tasks : =============== Consistency Check Reoccurrence = 168 hrs Next Consistency check launch = 04/04/2020, 03:00:00 Patrol Read Reoccurrence = 168 hrs Next Patrol Read launch = 04/04/2020, 03:00:00 Battery learn Reoccurrence = 670 hrs Next Battery Learn = 04/06/2020, 03:00:00 OEMID = Intel Physical Drives = 24 PD LIST : ======= ----------------------------------------------------------------------------- EID:Slt DID State DG Size Intf Med SED PI SeSz Model Sp Type ----------------------------------------------------------------------------- 0:0 1 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:1 7 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:2 22 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:3 23 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:4 24 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:5 13 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:6 14 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1 EMC1800 U - 0:7 8 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:8 9 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:9 4 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1 EMC1800 U - 0:10 10 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:11 3 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:12 11 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:13 25 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:14 26 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:15 27 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:16 28 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1 EMC1800 U - 0:17 2 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:18 12 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1 EMC1800 U - 0:19 6 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:20 5 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:21 29 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:22 30 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1CLAR1800 U - 0:23 31 UGUnsp - 1.610 TB SAS HDD N N 4 KB STTBSKD1 EMC1800 U - ----------------------------------------------------------------------------- EID-Enclosure Device ID|Slt-Slot No.|DID-Device ID|DG-DriveGroup DHS-Dedicated Hot Spare|UGood-Unconfigured Good|GHS-Global Hotspare UBad-Unconfigured Bad|Onln-Online|Offln-Offline|Intf-Interface Med-Media Type|SED-Self Encryptive Drive|PI-Protection Info SeSz-Sector Size|Sp-Spun|U-Up|D-Down|T-Transition|F-Foreign UGUnsp-Unsupported|UGShld-UnConfigured shielded|HSPShld-Hotspare shielded CFShld-Configured shielded|Cpybck-CopyBack|CBShld-Copyback Shielded Cachevault_Info : =============== --------------------------------------------------------- Model State Temp Mode MfgDate Next Learn --------------------------------------------------------- CVPM02 Optimal 30C - 2014/11/29 2020/04/06 03:14:47 --------------------------------------------------------- [root@localhost home]# /opt/MegaRAID/storcli/storcli /c0/vall show all Controller = 0 Status = Success Description = No VDs have been configured [root@localhost home]# /opt/MegaRAID/storcli/storcli /c0/vall set accesspolicy=rw Controller = 0 Status = Success Description = No VDs have been configured [root@localhost home]# /opt/MegaRAID/storcli/storcli /c0/v0 set accesspolicy=rw Controller = 0 Status = Failure Description = None Detailed Status : =============== ------------------------------------------------- VD Property Value Status ErrMsg ErrCd ------------------------------------------------- 0 - - Failed Invalid VD number 255 ------------------------------------------------- [root@localhost home]# /opt/MegaRAID/storcli/storcli /c0 jbod0 start init[Full][Force] syntax error, unexpected TOKEN_JBOD, expecting TOKEN_FLUSH Storage Command Line Tool Ver 1.21.06 Nov 18, 2016 (c)Copyright 2016, AVAGO Corporation, All Rights Reserved. help - lists all the commands with their usage. E.g. storcli help help - gives details about a particular command. E.g. storcli add help List of commands: Commands Description ------------------------------------------------------------------- add Adds/creates a new element to controller like VD,Spare..etc delete Deletes an element like VD,Spare show Displays information about an element set Set a particular value to a property get Get a particular value to a property compare Compares particular value to a property start Start background operation stop Stop background operation pause Pause background operation resume Resume background operation download Downloads file to given device expand expands size of given drive insert inserts new drive for missing transform downgrades the controller /cx Controller specific commands /ex Enclosure specific commands /sx Slot/PD specific commands /vx Virtual drive specific commands /dx Disk group specific commands /fall Foreign configuration specific commands /px Phy specific commands /[bbu|cv] Battery Backup Unit, Cachevault commands /jbodx JBOD drive specific commands Other aliases : cachecade, freespace, sysinfo Use a combination of commands to filter the output of help further. E.g. 'storcli cx show help' displays all the show operations on cx. Use verbose for detailed description E.g. 'storcli add verbose help' Use 'page=[x]' as the last option in all the commands to set the page break. X=lines per page. E.g. 'storcli help page=10' Use J as the last option to print the command output in JSON format Command options must be entered in the same order as displayed in the help of the respective commands. [root@localhost home]# /opt/MegaRAID/storcli/storcli /c0 jbod0 start init[Full][Force] syntax error, unexpected TOKEN_JBOD, expecting TOKEN_FLUSH Storage Command Line Tool Ver 1.21.06 Nov 18, 2016 (c)Copyright 2016, AVAGO Corporation, All Rights Reserved. help - lists all the commands with their usage. E.g. storcli help help - gives details about a particular command. E.g. storcli add help List of commands: Commands Description ------------------------------------------------------------------- add Adds/creates a new element to controller like VD,Spare..etc delete Deletes an element like VD,Spare show Displays information about an element set Set a particular value to a property get Get a particular value to a property compare Compares particular value to a property start Start background operation stop Stop background operation pause Pause background operation resume Resume background operation download Downloads file to given device expand expands size of given drive insert inserts new drive for missing transform downgrades the controller /cx Controller specific commands /ex Enclosure specific commands /sx Slot/PD specific commands /vx Virtual drive specific commands /dx Disk group specific commands /fall Foreign configuration specific commands /px Phy specific commands /[bbu|cv] Battery Backup Unit, Cachevault commands /jbodx JBOD drive specific commands Other aliases : cachecade, freespace, sysinfo Use a combination of commands to filter the output of help further. E.g. 'storcli cx show help' displays all the show operations on cx. Use verbose for detailed description E.g. 'storcli add verbose help' Use 'page=[x]' as the last option in all the commands to set the page break. X=lines per page. E.g. 'storcli help page=10' Use J as the last option to print the command output in JSON format Command options must be entered in the same order as displayed in the help of the respective commands. [root@localhost home]# [root@localhost home]# /opt/MegaRAID/CmdTool2/CmdTool2 -V Intel(R) RAID Command Line Utilities Version 2 Ver 8.07.15 Feb 27, 2014 (c)Copyright 2014, LSI Corporation, All Rights Reserved. Exit Code: 0x00 [root@localhost home]#