topic Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the in Mobile and Desktop Processors

I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

idata — Mon, 06 Feb 2017 17:21:04 GMT

I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.

I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.

However, in the above combination, the idle state of the linux system is 1.2Ghz, and when the program is run, the max frequency is only 2.6Ghz.

Motherboard setup seems to be done normally.

Using the "cpupower frequency-info" command, the hardware limits are set to 1.2Ghz - 2.6Ghz as shown below.

I ask for technical support on how to enable cpu speeds up to 3.5Ghz in the above environment.

-------------------------------------------------- -------------------------------------------------- -----------

Analyzing CPU 0:

Driver: acpi-cpufreq

CPUs which run at the same hardware frequency: 0

CPUs need to have their frequency coordinated by software: 0

Maximum transition latency: 10.0 us

Hardware limits: 1.20 GHz to 2.60 GHz

Available frequency steps: 2.60 GHz, 2.60 GHz, 2.50 GHz, 2.40 GHz, 2.30 GHz, 2.20 GHz, 2.10 GHz, 2.00 GHz, 1.90 GHz, 1.80 GHz, 1.70 GHz, 1.60 GHz, 1.50 GHz, 1.40 GHz, 1.30 GHz, 1.20 GHz

Available cpufreq governors: powersave ondemand userspace performance

Current policy: frequency should be within 1.20 GHz and 2.60 GHz.

The governor "ondemand" may decide which speed to use

Within this range.

Current CPU frequency: 1.20 GHz (asserted by call to hardware)

Boost state support:

Supported: yes

Active: yes

-------------------------------------------------- -------------------------------------------------- -----------

Thank you.

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

KL2 — Thu, 09 Feb 2017 02:31:10 GMT

Could this be erratum HSE49 / HSE54 here: http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-v3-spec-update.pdf http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-v3-spec-update.pdf

Supermicro X10DRD BIOS is up to date? BIOS defaults set after BIOS upgrade?

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

Amy_C_Intel — Sat, 11 Feb 2017 02:01:03 GMT

Gize2, thank you for that information.

SANG-HYUN_HAN, please follow the suggestion mentioned above, and let us know how it goes.

Regards,

Amy.

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

Amy_C_Intel — Wed, 22 Feb 2017 20:29:38 GMT

SANG-HYUN_HAN, were you able to follow the suggestion mentioned above?

Regards,

Amy.

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

idata — Thu, 23 Feb 2017 16:30:31 GMT

Thank you for your good suggestion.

But after BIAS upgrage, my PC still has E5-2690 CPU running at the highest frequency of 2.6Ghz.

The CentOS OS version is 6.5 and the motherboard is supermicro's X10DAi-O.

Is there any way to solve the problem that the turbo Boost frequency suggested by the spec can not be used?

I look forward to the advice of my great advisers.

Regards,

S.H.Han

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

idata — Thu, 23 Feb 2017 16:32:14 GMT

My CPU is E5-2690 V3. .......... please help me!!!

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

idata — Mon, 27 Feb 2017 18:48:50 GMT

What is the BIOS version you upgraded to? The latest should be; https://www.supermicro.com/support/resources/results.aspx Super Micro Computer, Inc. | Support

Bear in mind that this feature will be reached when need it, there is no option to turn it on or off. The maximum turbo frequency indicates the highest possible frequency achievable when conditions allow the processor to enter turbo mode. Intel® Turbo Boost Technology frequency varies depending on workload, hardware, software, and overall system configuration.

Availability and frequency upside of Intel® Turbo Boost Technology 2.0 state depends upon a number of factors including, but not limited to, the following:

Type of workload
Number of active cores
Estimated current consumption
Estimated power consumption
Processor temperature

For further reference visit http://www.intel.com/content/www/us/en/architecture-and-technology/turbo-boost/turbo-boost-technology.html Intel® Turbo Boost Technology 2.0.

Regards,

Amy.

Re: I have a system using linux centos 6.5 OS, a "supermicro X10DRD" mother board and two "E5-2690 V3" CPUs.I know that CPU's maximum frequency is 2.6Ghz, but turboBoost function will clock up to 3.5Ghz.However, in the above combination, the idle state of the

idata — Mon, 06 Mar 2017 17:51:58 GMT

SANG-HYUN_HAN, hope the information posted above help you, and if you need further assistance let us know.

Regards,

Amy.