topic Hi, in Software Archive

DCM /FW Install Issues - PLEASE READ!

Colleen_C_Intel — Wed, 30 Sep 2015 06:15:55 GMT

There are multiple possible failure/error situations during DCM installs/upgrades. There is also a built in limitation of attempts in some cases at 20. If you have issues after 2 or 3 attempts, please follow the instructions below.

There are 2 errors that have solutions already posted:
- IF the error is the Installer mentions other Microsoft Hotfixes or patches, you do NOT have a problem unless you see other issues with the installation.
- If the error is saying you have 0 space, you need to remove the file "C:\Program Files (x86)\Intel\RSDCM" and try installation again

For other errors, please supply us with the following information: (1, 2, and 3 are definitely all required)
Note: it is VERY IMPORTANT that you check and accurately report your exact conditions as there are many combinations with different end results.
1. Is the camera a peripheral ordered from Intel or is it integrated into the PC? Being locked or in recovery mode differs between peripheral and integrated cameras.
2. In Device Manager, what is listed under Imaging Devices? (nothing, virtual driver, RGB, depth, webcam, etc..)
3. In Device Manager, what is listed under USB Devices as a RealSense camera? (IF listed, does it end with the camera model number or with the word device?
4. Are there any error codes (-4 is general camera failure; -3 is failed to init camera).
5. Include install logs.

Hi,

Charles_H_1 — Fri, 02 Oct 2015 09:25:00 GMT

Hi,

I have a problem with the install of the SDK.

Setup Wizard (ended prematurely details: To install this program at a later time, run Wizard again.
Click the Finish buton to exit the Setup Wizard,

Camera INTEL REALSENSE 3D CAMERA (R200) DEVELOPER KIT (order from Intel)

Version SDK 6.0.21.6598

Laptop details: Windows 10 Home Processor Intel Core i7-3632QM and 8GB Ram.

How can I fix this problem?

Best regards,

Charles

Hello,

Joseph_L_ — Fri, 02 Oct 2015 15:20:01 GMT

Hello,

I'm having a problem installing the DCM R200 (version 2.0.3.39488)

I'm getting this error "The Installer failed to detect an Intel RealSense 3D Camera on this system. The installation was terminated."

I'm trying to install this on a Surface Pro 3, the R200 is plugged-in directly to the USB 3.0 port. OS is Windows 10 Enterprise 64-bit.

---------------------

1. Is the camera a peripheral ordered from Intel or is it integrated into the PC? Being locked or in recovery mode differs between peripheral and integrated cameras.

Camera was ordered from Intel.

2. In Device Manager, what is listed under Imaging Devices? (nothing, virtual driver, RGB, depth, webcam, etc..)

The only things listed are Microsoft LifeCam Front and Microsoft LifeCam Rear

3. In Device Manager, what is listed under USB Devices as a RealSense camera? (IF listed, does it end with the camera model number or with the word device?

Not listed

4. Are there any error codes (-4 is general camera failure; -3 is failed to init camera).

N/A

5. Include install logs.

Where is this stored?

-----------------

Thanks for any help.

-Joseph

If you aren't seeing the

Colleen_C_Intel — Fri, 02 Oct 2015 15:29:30 GMT

If you aren't seeing the camera at all, in Dev. Mgr or by the Software - then you probably are having a USB 3 issue. Do you have more than one port you could try? Do you have another system you could try the camera in? Can you look under USB Controllers and see what the details are on the 3.0 controller?

Here's a screenshot of the

Joseph_L_ — Fri, 02 Oct 2015 18:22:40 GMT

Here's a screenshot of the USB controllers in Device Manager on my Surface Pro 3 and I'll try a second machine.

There's only 1 USB 3 port,

Colleen_C_Intel — Fri, 02 Oct 2015 18:32:36 GMT

There's only 1 USB 3 port, right? And you don't have anything else plugged into it (like a hub or port expander). Do other USB 3 devices work ok? Did it ever work?

Yes, there's only 1 USB 3

Joseph_L_ — Fri, 02 Oct 2015 20:18:49 GMT

Yes, there's only 1 USB 3 port and I plugged in the R200 directly (I'm not using a hub). The port also works since I usually I have a Toshiba dynadock that I use. But for this test, I did not have the dynadock plugged-in.

Also I was wondering if it

Joseph_L_ — Fri, 02 Oct 2015 20:22:03 GMT

Also I was wondering if it matters that I'm on Windows 10 Enterprise and not Windows 10 Pro.

Hi,

Martin_Z_2 — Sat, 03 Oct 2015 11:38:49 GMT

Hi,

I have problems with installing DCM. I tried install it several times, but every time it ended with the same error:

Intel® RealSense™ Depth Camera Manager F200 Setup Wizard ended prematurely because of an error(s).

Details

Intel® RealSense™ 3D camera firmware update failed.

The installer failed to update the firmware of your Intel® RealSense™ 3D camera. The camera firmware may be corrupted. Contact your computer manufacturer for recovery instructions.

Error code: -17

Additional information:

1. I have Intel ultrabook development system with integrated camera.

Can please anyone help me?

Martin

Hello,

Joseph_L_ — Mon, 05 Oct 2015 15:38:37 GMT

Hello,

I've tried installing on a second machine and this time I'm getting an error code: -10000 when installing the DCM.

1. Is the camera a peripheral ordered from Intel or is it integrated into the PC? Being locked or in recovery mode differs between peripheral and integrated cameras.

Camera was ordered from Intel.

2. In Device Manager, what is listed under Imaging Devices? (nothing, virtual driver, RGB, depth, webcam, etc..)

Imaging devices

- Intel(R) RealSense(TM) 3D Camera (R200) Depth
- Intel(R) RealSense(TM) 3D Camera (R200) Left-Right
- Intel(R) RealSense(TM) 3D Camera (R200) RGB

3. In Device Manager, what is listed under USB Devices as a RealSense camera? (IF listed, does it end with the camera model number or with the word device?

Where is this listed?

4. Are there any error codes (-4 is general camera failure; -3 is failed to init camera).

During the installation of the DCM I got error code -10000.

5. Include install logs.

Where is this stored?

I have a Dell XPS on Windows

Chi_T_ — Mon, 05 Oct 2015 23:16:00 GMT

I have a Dell XPS on Windows 10 (Home) and I did not have any installation problem at all. I cleaned out my old install (Release 2 of the SDK) first.

I plugged in the new R200 to a backside USB3 port and installed my DCM for R200 (intel_rs_dcm_r200_2.0.3.39488.exe) OK. When I next plugged in the F200 (to a Front-side USB3 port), the PC went to the web and install new drivers for the F200 automatically. And when I invoked DCM for F200 (intel_rs_dcm_f200_1.4.27.41944.exe), it said that I had a newer driver version already. Next I installed the off-line SDK (intel_rs_sdk_offline_package_r4_6.0.21.6598.exe) and things went OK too. I did not have to install the driver from Creative (C3DG_0800_PCAPP_DRV_EN_1_00_07a.exe) as it said that I already had a newer driver.

I also had an older Senz3D camera, so I also installed the 2013 SDK (intel_pc_sdk_offline_package_t_1.8.13842.0.exe) - OK also.

And so far I am glad to report that all 3 cameras are working OK for me - at the same time (lucky, I guess). The old 2013 SDK still gives me Depth data OK, but the newer RS SDK Release 4 only gave me the RGB data for the Senz3D camera.

I am not able to run the

Darrel_K_ — Thu, 08 Oct 2015 15:49:38 GMT

I am not able to run the Camera Manager installer. I get the following message:

The installer failed to detect an Intel® RealSense™ 3D camera on this system. The installation was terminated.

1. The camera was ordered from Intel

2. Device Manager shows:

Inter(R) RealSense(TM) 3D Camera (R200) Depth
Inter(R) RealSense(TM) 3D Camera (R200) Left-Right
Inter(R) RealSense(TM) 3D Camera (R200) RGB

3. Not listed by name. Listed as USB Composite Device. This camera is plugged directly into the back of the PC into a USB3 port.

4. No error codes.

5. Not sure where to find the log if there is one.

Other information:

Windows 10 Enterprise, Intel i7-4771, 32GB DDR3

Any help would be great. Thanks

Firmware update problem -4

Keith_S_ — Mon, 12 Oct 2015 06:09:53 GMT

Firmware update problem -4 with Lenovo B50-30 All In One updated to Windows 10 from factory reset. Answers to most if not all questions in attached doc. No camera seen under images but it appears under system devices a Front. No camera application can find the camera. Regards, Keith

i have f200, when installing

Houman_Z_ — Fri, 16 Oct 2015 22:21:03 GMT

i have f200, when installing last dcm it shows error for firmware update, but i can install version 1.2 but windows hello dies not come, i have windows 10 pro installed on my macbook pro bootcamp usb3 and 4rd generation cpu, please help me to enable my camera for windows hello, creative firmware utility tells me that firmware is uptodate

no one to help

Houman_Z_ — Sun, 18 Oct 2015 01:24:08 GMT

no one to help

i want to know the camera sent by intel is correct or not

maybe the problem is with camera

when i plug usb even the gree light of camera does not turn on?

how i ahve to inform intel to send new camera to me?

regards

houman zarkesh

Keith, do you have integrated

Xusheng_L_Intel — Wed, 21 Oct 2015 15:43:52 GMT

Keith, do you have integrated F200 in this computer? how many camera did you connect to this computer at same time? Thanks, David

Keith S. wrote:

Firmware update problem -4 with Lenovo B50-30 All In One updated to Windows 10 from factory reset. Answers to most if not all questions in attached doc. No camera seen under images but it appears under system devices a Front. No camera application can find the camera. Regards, Keith

Hi,

uzi_b_ — Thu, 22 Oct 2015 01:58:51 GMT

i've been trying to install f200 on usb3 ports running intel_rs_dcm_f200_1.4.27.41944.exe on two different Windows 10 pro machines but keep getting this:

The installer failed to detect an Intel® RealSense™ 3D camera on this system. The installation was terminated. (Also attached capture)

on both machines device manager only shows Creative VF0800 under Sound, video and game controllers, but nothing under imaging devices.

any ideas?

Cheers,

Uzi

Maybe the firmware in this

Xusheng_L_Intel — Fri, 23 Oct 2015 17:45:41 GMT

Maybe the firmware in this camera is too old. Where and when did you get this camera? Could you provide a pic? Thanks!

When installing DCM 1.4.27

chris_g_4 — Fri, 23 Oct 2015 20:33:41 GMT

When installing DCM 1.4.27.41944 I receive:

USB3.0 Host Controller driver is required for Depth Camera Manager Installer to continue. Please download and install the Intel® USB 3.0 eXtensible Host Controller Driver from below location and restart DCM installation.

Using Renesas USB 3.0 controller. The intel recommended drivers are for C610+ is there no support for the C600?

Ok am in the same boat as the

kelly_t_ — Thu, 29 Oct 2015 19:44:00 GMT

Ok am in the same boat as the rest of you all but all the software installed good its just wont turn on or not connected i getnder

not connected it say under camera explorer but under the driver manger is show ok and all the installed went fine it just not turning on

and it the f200 camera DAM IT I NEED windows 8.1 or higher i have windows 7 64

i got a bad camera each got it to work one or two times then it stops working keep disconnecting usb