The problem in using multiqueue in sr-iov

[User1589337670482787]

Hello, I am now in test sriov mode of the virtual machine network performance, i using two 82599 nic CARDS created eight vf respectively, and then took out two vf card to a virtual machine. During the test by ethtool -S I found that only a queue receiving packets, 

through the datasheet i found that if need use multiple queue in vf need configue DCB and tc.

Now i had configuration DCB and TC，but receive packages can only use single queue problem still unsolved

How should I Do to use multiple queues to receive packets in vf?

[root@host ~]# dcbtool gc eth5 dcb 

Command:   Get Config

Feature:   DCB State

Port:    eth5

Status:   Successful

DCB State: on

[root@host ~]# dcbtool gc eth5 pg

Command:   Get Config

Feature:   Priority Groups

Port:    eth5

Status:   Successful

Enable:   true

Advertise: true

Willing:   true

up2tc:    0 1 2 3 4 5 6 7

pgpct:    13% 13% 13% 13% 12% 12% 12% 12%

pgid:    0 1 2 3 4 5 6 7

uppct:    100% 100% 100% 100% 100% 100% 100% 100%

pg strict: 0 0 0 0 0 0 0 0

num TC's:  8

[root@host ~]# tc qdisc add dev eth5 root mqprio num_tc 8

[root@host ~]# tc qdisc show dev eth5

qdisc mqprio 800a: root tc 8 map 0 1 2 3 4 5 6 7 0 1 1 1 3 3 3 3 

       queues:(0:0) (1:1) (2:2) (3:3) (4:4) (5:5) (6:6) (7:7) 

qdisc pfifo_fast 0: parent 800a:8 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:7 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:6 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:5 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:4 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

qdisc pfifo_fast 0: parent 800a:1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1

[User1589337670482787]

 And there is one another question, in the 82599 datasheet, it said that if turn off DCB and set RSS on, when create 16 vf, one pool would be get 4 RSS. IN my test, i found there are 4 RSS when use ethtool -l $NIC. But in the VM, i use ethtool -S $nic, only get 2 rx queue. where is the problem.