- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Excuse me, I want to measure the X710-BM2 (IC) 10G Fiber signal (TX/RX) and use "lanconf64e.efi" tool to set the settings But there will be many situations:
Tx: Only 10G_PRBS31 can be used for measurement. If you switch to other options (PRBS9/PRBS31/Square
Tx:
Only 10G_PRBS31 can be used for measurement. If you switch to other options (PRBS9/PRBS31/Square 8), the signal will disappear immediately.
Measuring DUT requires PRBS9 & Square 8 for measurement.
RX:
Unable to find suitable instructions for measurement (EX: DUT Loopback or read PRBS BER)
You can only see the BASE-T option in IEEE BER Test
Use BERT (test instrument) to drive the PRBS signal into the RX of the chip through the test fixture
And
We also encountered the same situation when measuring E810-XXVAM2 25G Fiber.
Any suggestions or a better testing tool?
Link Copied
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi DavidCFWei,
Thank you for reaching out to the Intel community. We acknowledge receipt of your concern and want to assure you that assisting you is our top priority. To effectively troubleshoot the issue you're facing, we require some additional information from your end.
Could you kindly provide the following details?
1. System Model:
2. Purpose of measuring the fiber signal:
Your prompt response with this information will greatly assist us in diagnosing and resolving the issue as quickly as possible.
We look forward to hearing from you soon.
Best Regards,
Simon
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi , Simon
1.System Model:
CPU : Intel CPU (FHF)
OS : Win 11
Lan Controller : X710-BM2 (10G) , E810-XXVAM2 (25G)
2.Purpose of measuring the fiber signal:
When making a small board using these two ICs, it is necessary to measure the signal quality on the small board.
Please check this .
Any questions , please let me know .
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello DavidCFWei,
Thank you for the details.
Since you are using a custom board and you wish to measure the fiber signals for X710 10G card, we suggest posting this query in our embedded community forum.
Kindly use the below link and submit your request.
https://community.intel.com/t5/Embedded-Connectivity/bd-p/embedded-networking-connectivity
Thank you for using Intel products and services.
Regards,
Sachin KS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello, @Sachinks:
Thank you for contacting Intel Embedded Community.
We need to clarify that this forum is not related to an Embedded Platform.
Due to this, the customer request is out of our scope of support.
Please consider this information when you provide the previous suggestion, or transfer any forums to the channel that you mentioned in your previous communication.
Best regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello DavidCFWei,
Good Day!
I'm reaching out regarding your concern that requires the attention of the FPGA team. Please get in touch with them for further support. Here's the link to connect with them: FPGA Team Community
Best Regards,
Simon
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi DavidCFWei,
Thank you for contacting Intel.
This is the first follow-up regarding the issue you reported to us.
We wanted to inquire whether you had the opportunity to review the plan of action (POA) we provided.
Feel free to reply to this message, and we'll be more than happy to assist you further.
Regards,
Simon
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello DavidCFWei,
Good day!
We wanted to let you know that we are closing this request. A dedicated team handles these queries, and as previously mentioned, we kindly ask you to contact them directly.
If you have any further questions in the future, please don't hesitate to reach out. Feel free to start a new conversation, as this thread will no longer be monitored.
Best regards,
Simon

- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page