Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Altera_Forum
Honored Contributor I
804 Views

Max10 Eval Kit User Flash Memory IP

Hey everyone, I've been trying  

As a sidenote - I have read the MAX10 User Flash Memory guide in its entirety no fewer than 3 times, however, I have almost zero experience in verilog. 

 

I'm trying to use the push buttons on my development kit to "one step" my way through the Altera Flash IP core, and reading out significant signals to the leds on board as a troubleshooting tool. My problem is currently, I try to write to the CSR control register, then read back the CSR control register to verify my changes went though - they never do. Any guidance as to where to go from here (or if I'm completely off course..) would be greatly appreciated. Here's my verilog code. Thanks! 

 

module FlashMemory( 

clock, 

pbs, 

led 

); 

 

 

input clock; 

input [3:0]pbs; 

output [4:0]led; 

 

 

///////////////////////// 

reg[31:0] writedata = 32'h00000000; 

reg[31:0] readdata; 

reg[15:0] dataaddress = 16'h0004; 

 

 

reg[31:0] readdatacopy = 32'hFFFFFFFF; 

 

 

reg datawrite = 1'b0; 

reg dataread = 1'b0; 

reg burstcount = 1; 

reg busy; 

///////////////////////// 

reg[31:0] csrwritedata = 32'h001FFFFF; 

reg[31:0] csrreaddata; 

reg[15:0] csraddress = 16'h0001; 

 

 

reg csrhighbit = 1'b1; 

 

 

reg csrwrite = 1'b0; 

reg csrread= 1'b0; 

///////////////////////// 

reg reset; 

wire pllclock; 

wire locked; 

wire readdataok; 

reg [4:0]led = 5'b11111; 

 

 

reg writebutton; 

reg readbutton; 

reg csrwritebutton; 

reg csrreadbutton; 

reg csrwriteprotection; 

reg dummy = 1'b0; 

reg [31:0] writetimer = 0; 

 

 

always @(posedge pllclock) begin  

 

 

if(dummy)begin 

reset <= 1'b0; 

end 

///////////////////////// 

else begin 

reset <= 1'b1; 

 

 

csrwritebutton <= pbs[0]; 

csrwriteprotection <= pbs[1]; 

csrreadbutton <= pbs[2]; 

 

 

 

 

if(!pbs[0] && csrwritebutton)begin 

csrwritedata <= 32'h001FFFFF; 

csrwrite <= 1'b1; 

end else if(!pbs[1] && csrwriteprotection) begin 

csrwritedata <= 32'hFFFFFFFF; 

csrwrite <= 1'b1; 

end else begin 

csrwrite <= 1'b0; 

end 

 

 

if(!pbs[2] && csrreadbutton) begin 

csrread <= 1'b1; 

end else begin 

csrread <= 1'b0; 

end 

 

 

if(!csrreaddata[31]) begin 

csrhighbit <= csrreaddata[31]; 

end 

 

 

if (csrread) begin 

led[0] <= 1'b0; 

end  

 

 

if (csrhighbit)begin 

led[4] <= 1'b1; 

end 

if (!csrhighbit)begin 

led[4] <= 1'b0; 

end 

 

 

 

 

end 

end 

FlashIP FlashIP_inst ( 

.clock (pllclock), // clk.clk 

.reset_n (reset), // nreset.reset_n 

.avmm_data_addr (dataaddress), // data.address 

.avmm_data_read (dataread), // .read 

.avmm_data_writedata (writedata), // .writedata 

.avmm_data_write (datawrite), // .write 

.avmm_data_readdata (readdata), // .readdata 

.avmm_data_waitrequest (busy), // .waitrequest 

.avmm_data_readdatavalid (readdataok), // .readdatavalid 

.avmm_data_burstcount (burstcount), // .burstcount 

.avmm_csr_addr (csraddress), // csr.address 

.avmm_csr_read (csrread), // .read 

.avmm_csr_writedata (csrwritedata), // .writedata 

.avmm_csr_write (csrwrite), // .write 

.avmm_csr_readdata (csrreaddata) // .readdata 

&nbsp;); 

 

 

 

 

 

 

FlashPLL FlashPLL_inst ( 

.inclk0 ( clock ), 

.c0 ( pllclock ), 

.locked ( locked) 

&nbsp;); 

 

 

 

 

endmodule
0 Kudos
0 Replies
Reply