Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Novice
136 Views

10m50 development board SDRAM implementing.

Jump to solution

hi everyone,

i am new at FPGA world. I am using 10m50daf484c6ges development board. i want to run large codes in nios II, so i need to use SDRAM but i could not implement sdram. i tried all of the ways where i find in internet but i couldn't be successful. can anybody help me?

0 Kudos

Accepted Solutions
Highlighted
Employee
4 Views

Re: 10m50 development board SDRAM implementing.

Jump to solution

Hi,

Upon checking in design store, there is a Intel MAX 10 FPGA Development Kit with DDR3 UniPHY tutorial:

https://fpgacloud.intel.com/devstore/platform/15.0/Standard/design-example-max10-10-ddr3-300mhz-unip...

 

But I found that the project build in Quartus Prime v15.0 version, it might be some IP not compatible to use in Quartus Prime Lite v18.1.

You can try to download and look into the design.

 

There are some tutorials for Intel MAX 10 Development Kit DDR3:

https://fpgacloud.intel.com/devstore/?page=1&search=ddr3

 

For more information in MAX 10 External Memory Interface, you may need to refer the document as below:

https://www.intel.com/content/dam/www/programmable/us/en/pdfs/literature/hb/max-10/ug_m10_emi.pdf

 

Thanks

View solution in original post

5 Replies
Highlighted
Employee
4 Views

Re: 10m50 development board SDRAM implementing.

Jump to solution

Hi, 

 

May I know the information as below: 

1. Are you using Intel MAX 10 FPGA Developmet Kit as I can found the information for "10m50daf484c6ges development board" in link below: 

https://www.intel.com/content/www/us/en/programmable/products/fpga/max-series/max-10/design-tools.ht...

2. The Nios II software version used

 

Could you provide me the full design file for further investigate/

 

Thanks

0 Kudos
Highlighted
Novice
4 Views

Re: 10m50 development board SDRAM implementing.

Jump to solution

I am using Intel MAX 10 FPGA Development Kit which has dual ethernet port.

And i am using Quartus Prime 18.1 lite edition with NIOS II eclipse Mars.2 version 4.5.2

 

is there any tutorial or example for adding sdram on this development kit?

can i add sdram with lite edition quartus?

 

And which IP core do I need to use for communication with sdram, sdram controller or ddr3 sdram controller with UNIPHY?

 

Thank you for your support!

0 Kudos
Highlighted
Employee
5 Views

Re: 10m50 development board SDRAM implementing.

Jump to solution

Hi,

Upon checking in design store, there is a Intel MAX 10 FPGA Development Kit with DDR3 UniPHY tutorial:

https://fpgacloud.intel.com/devstore/platform/15.0/Standard/design-example-max10-10-ddr3-300mhz-unip...

 

But I found that the project build in Quartus Prime v15.0 version, it might be some IP not compatible to use in Quartus Prime Lite v18.1.

You can try to download and look into the design.

 

There are some tutorials for Intel MAX 10 Development Kit DDR3:

https://fpgacloud.intel.com/devstore/?page=1&search=ddr3

 

For more information in MAX 10 External Memory Interface, you may need to refer the document as below:

https://www.intel.com/content/dam/www/programmable/us/en/pdfs/literature/hb/max-10/ug_m10_emi.pdf

 

Thanks

View solution in original post

Highlighted
Novice
4 Views

Re: 10m50 development board SDRAM implementing.

Jump to solution

Great Thanks! i will try these ways and i will tell you the result.

0 Kudos
Highlighted
Novice
4 Views

Re: 10m50 development board SDRAM implementing.

Jump to solution

Thank you again Sir! finally i could communicate with the sdram.

Problem was the version of Quartus. i complied the same project on quartus II V.15.0 web edition then i worked.

0 Kudos