Re: EMIF on Stratix 10 Dev Kit miss board file

Altera_Forum · ‎06-22-2018

Hi all

i'm working on EMIF for stratix 10 Dev KIT

while generating the IP i can't find my board listed in the presets

how can i add it ?

if i can't what should i do ?

Thanks

Altera_Forum · ‎06-25-2018

Hi,

Which Quartus Version & Edition are you using?

Check the availability of supported devices & then download it,

https://www.altera.com/downloads/download-center.html

Let me know if this has helped resolve the issue you are facing or if you need any further assistance.

Best Regards

Vikas Jathar

(This message was posted on behalf of Intel Corporation)

Altera_Forum · ‎06-25-2018

i'm using quartus pro 17.1

and i'm facing problem generating a working EMIF example design

is there a portable preset that i can use ?

Altera_Forum · ‎06-27-2018

Hi,

--- Quote Start ---

while generating the IP i can't find my board listed in the presets

--- Quote End ---

Currently it is not available, In future it might get available.

--- Quote Start ---

if i can't what should i do ?

--- Quote End ---

You can download Golden Top Design, extract it & open .qpf file from your Quartus tool: (es edition, 17.1 (https://www.altera.com/content/dam/altera-www/global/en_us/support/boards-kits/stratix10/fpga/stratix10gx_1sg280uf50_fpga_revd_v17.1ib240_v1.0a.zip))

https://www.altera.com/products/boards_and_kits/dev-kits/altera/kit-s10-fpga.html

Let me know if this has helped resolve the issue you are facing or if you need any further assistance.

Best Regards

Vikas Jathar

(This message was posted on behalf of Intel Corporation)

Altera_Forum · ‎06-27-2018

Hi ,

i have already downloaded the package and tried generating several example designs and i always get calibration failed and i can't "create memory interface connection" in the EMIF Toolkit , so i can't even debug my design

i already posted my problem about "create memory interface connection" you can find it in this link :

https://www.alteraforum.com/forum/showthread.php?t=59053

and could you please provide me with a full datasheet of the daughter cards that came with the board :

-ALTERA DRAM X72 DAUGHTER CARD

-ALTERA RLDRAM3 X36 DAUTHER CARD

-ALTERA EMIF HILO

i have also tested the examples in the package after downloading the bit stream , in the ISSP i have calibration fail and i tried to run Board Test System (bts) but the gui can't detect the jtag cable

so i'm facing so many problems , i don't have much time and i need help

thanks

Altera_Forum · ‎07-02-2018

Hi,

--- Quote Start ---

i have already downloaded the package and tried generating several example designs and i always get calibration failed and i can't "create memory interface connection" in the EMIF Toolkit , so i can't even debug my design

--- Quote End ---

Refer the User guide,

https://www.altera.com/content/dam/altera-www/global/en_us/pdfs/literature/ug/ug-20120.pdf

For Daughter cards refer the following link,

https://www.altera.com/products/boards_and_kits/daughter-cards.html

--- Quote Start ---

i have also tested the examples in the package after downloading the bit stream , in the ISSP i have calibration fail and i tried to run Board Test System (bts) but the gui can't detect the jtag cable

--- Quote End ---

Have you installed the drivers, if not, Refer following link & install before using it,

https://www.altera.com/support/support-resources/download/drivers/dri-index.html

https://www.youtube.com/watch?v=wjwkdznh1py

Best Regards

Vikas Jathar

(This message was posted on behalf of Intel Corporation)