FPGA, SoC, And CPLD Boards And Kits
FPGA Evaluation and Development Kits
5892 Discussions

Event 113350 / How to send to analysis 1pc ALC3-1AB227640008_REP / EP4S100G5H40I1N

ADobr
Beginner
582 Views

Part found fail by Nokia R&D

0 Kudos
5 Replies
Zawani_M_Intel
Employee
416 Views

Hi Alina,

 

Please tell me the story of this part, how you discovered that it is fails? How it was measured?

0 Kudos
ADobr
Beginner
416 Views
Hi Wani, Please see attached the failure description. DC: 1549 PO: 20Z625813 Please provide RMA and shipping instructions in order to send the part to analysis. Thank you and Best Regards, [cid:image001.png@01D215AB.1E6879C0] Alina Dobri Supplier Quality Engineer Calea Torontalului DN6, km5.7 RO-300000 Timisoara Romania Phone number: 0040356474010 Creating value that increases customer competitiveness alina.dobri@flex.com<mailto:alina.dobri@flex.com> www.flextronics.com<http://www.flextronics.com/>
0 Kudos
Zawani_M_Intel
Employee
416 Views

Hi Alina,

 

Please share with me this details so we can move further ;

 

1. What is the failure rate? What is the failure rate vs. tested sample? Example: 2 out of 100 units.

 

2. What is the failure symptom? Please elaborate the failure symptom in detail. 

 

3. When did the failure happen? How did you discover the failure? 

 

4. How did you determine the failure? Please elaborate the procedures. 

 

5. Does the failure unit ever working before failure?

 

6. Did they violate solder re-flow temperature profiles, moisture sensitivity? Please provide the re-flow temperature profiles. 

 

7. Did you swap the failure device to a known good board? Is the failure following the device or board?

 

8. Is this a prototype build or volume/mass production?

 

9. Kindly provide quantitative investigation result that could proof the failure is Intel FPGA induced. 

 

 

Please do not share confidential information publicly. If you required private message, please do let us know.

 

Thanks!

 

Wani

 

0 Kudos
ADobr
Beginner
416 Views
Hi WaniMY, Please find the answers below. Please provide RMA and shipping instructions. 1. What is the failure rate? What is the failure rate vs. tested sample? Example: 2 out of 100 units. N/A 2. What is the failure symptom? Please elaborate the failure symptom in detail. SFI issue ADD2 to Obelix at room temperature 25⁰C 3. When did the failure happen? How did you discover the failure? In field. We do not have this information. 4. How did you determine the failure? Please elaborate the procedures. For common FPGA defects on 100/200G SDFEC items (eg. ADD2, Obelix, FlexFramer) we are supported by a list of corrective actions (provided by Nokia), a list that contains a description of the failures and the corrective action needed (repair indication, RMA note to supplier), based on the encountered defect. The way we determine the failure is mainly based on our experience and the indications received by R&D, due to the large number of failed boards and the variety of failures that we analyzed during the life cycle of these products. If a FPGA needs to be sent to the supplier, it is usually followed by a RMA note/request, as found mentioned above. 5. Does the failure unit ever working before failure? YES 6. Did they violate solder re-flow temperature profiles, moisture sensitivity? Please provide the re-flow temperature profiles. Everything was in correct profiles/paramaters 7. Did you swap the failure device to a known good board? Is the failure following the device or board? YES. After the replacement with a new device, the failure disappeared. 8. Is this a prototype build or volume/mass production? Mass production 9. Kindly provide quantitative investigation result that could proof the failure is Intel FPGA induced. If the issue is not due to soldering, after the FPGA has been replaced, everything works well. We ask Intel to re-test the device to ensure that it meets the necessary parameters required by Nokia. Thank you and Best Regards, Alina [cid:image001.png@01D5C486.F4C32870] Alina Dobri Supplier Quality Engineer Calea Torontalului DN6, km5.7 RO-300000 Timisoara Romania Phone number: 0040356474010 Creating value that increases customer competitiveness alina.dobri@flex.com<mailto:alina.dobri@flex.com> www.flextronics.com<http://www.flextronics.com/>
0 Kudos
Deshi_Intel
Moderator
416 Views

Hi Alina,

 

Same procedure here.

 

I will initiate private message discussion with you for FA analysis support on EP4S100G5H40I1N device.

 

Thanks.

 

Regards,

dlim

0 Kudos
Reply