Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Highlighted
Beginner
604 Views

Mavlink-Router is not working and Firmware version is coming unknown

Jump to solution

Hello

 

I am working on intel Aero RTF drone, I have set up the full drone mavlink-router was working as well as firmware version was showed up.

But Yesterday I reboot the drone now firmware version is coming unknown and the mavlink-router is also not starting up.

 

The screenshot of the status of mavlink-router:

Screenshot from 2019-03-19 14-59-41.png

 

The screenshot of the intel-aero-version:

Screenshot from 2019-03-19 15-00-51.png

 

Please help me with this, I am totally confused what happened after rebooting the drone that nothing is working now, before that everything was perfectly working.

 

Thanks and Regards

Utkarsh

0 Kudos

Accepted Solutions
Highlighted
Employee
33 Views
Hello UGoya, Since you have had this issue in a previous thread, will be possible to reinstall the OS, this time using Ubuntu 16.04.3, as this is the version that have been confirmed to work with the drone. You can find it here: http://old-releases.ubuntu.com/releases/16.04.3/ , by the name: ubuntu-16.04.3-desktop-amd64.iso Thank you and best regards, Eliza

View solution in original post

0 Kudos
6 Replies
Highlighted
Employee
33 Views
Hello UGoya, Thank you for your interest in the Intel Aero Ready to Fly drone. I notice that you FPGA version 0xc0, where it should be 0xc2. You are unable to connect to mavlink router because the FC is not recognized. And the reason why the FC is not recognized is most probably caused by the fact that you have an older version of FPGA. So I recommend you to firstly, update the FPGA with aero-rtf.jam as per: https://github.com/intel-aero/meta-intel-aero/wiki/02-Initial-setup#flashing-the-fpga and after this to flash again the Flight Controller, as per: https://github.com/intel-aero/meta-intel-aero/wiki/02-Initial-setup#flashing-the-flight-controller-r... Thank you and best regards, Eliza
0 Kudos
Highlighted
Beginner
33 Views

Hello Eliza

I have updated the FPGA version, and than again flashed the flight controller, but still the Firmware is coming to be unknown.

 

The screenshot of all the commands is:

Screenshot from 2019-03-19 16-59-10.png

And Mavlink-router is also not working.

So I am totally confused what is the problem present in the system

Thanks and Regards

Utkarsh

0 Kudos
Highlighted
Employee
34 Views
Hello UGoya, Since you have had this issue in a previous thread, will be possible to reinstall the OS, this time using Ubuntu 16.04.3, as this is the version that have been confirmed to work with the drone. You can find it here: http://old-releases.ubuntu.com/releases/16.04.3/ , by the name: ubuntu-16.04.3-desktop-amd64.iso Thank you and best regards, Eliza

View solution in original post

0 Kudos
Highlighted
Beginner
33 Views

Hello

 

It means I have to install everything again and do the flashing of all the the components again.

 

Regards

Utkarsh

0 Kudos
Highlighted
Employee
33 Views
Hello UGoya, Unfortunately, yes. The version 16.04.6 have not been test by us for Intel Aero RTF drone and Ubuntu 16.04.3 have been validated by Intel to work well with the drone. Thank you and best regards, Eliza
0 Kudos
Highlighted
Beginner
33 Views

Hello Eliza

 

I have installed everything again, and now everything is working fine.

 

Thanks for solving the issue.

 

Thanks and Regards

Utkarsh

0 Kudos