Intel® FPGA University Program
University Program Material, Education Boards, and Laboratory Exercises
1174 Discussions

intel quartus license setup window is not working in ubuntu

Qazi_Shahid
New Contributor I
1,888 Views

I have installed intel quartus prime standrad edition and running sudo ./quartus from directory home/intelFPGA/20.1/quartus/ the license setup window appears but it is blank, so I cannot add the license file that I have.

Kindly guide me regarding this issue.

0 Kudos
1 Solution
SyafieqS
Moderator
1,688 Views

Hi Qazi,


Still cant see the email. Can you check your private message?


View solution in original post

10 Replies
Qazi_Shahid
New Contributor I
1,856 Views

It ran successfully after deleting the sudo word in the terminal

command to run:

sudo ./quartus (didn't work)

./quartus (worked)

After that I gave the license file location.

But it is asking for a license file each time I restart the quartus software.

It also ran into some other error Which I mentioned here.

https://community.intel.com/t5/Intel-FPGA-University-Program/Problem-Installing-cyclone-V-Device-on-Quartus-prime-standarad/m-p/1256013/highlight/true#M4059

Kinldy look into it.

0 Kudos
SyafieqS
Moderator
1,848 Views

Hi Qazi,


Could you install following libraries?

Install libc6:i386, libncurses5:i386, libxtst6:i386, libxft2:i386, libstdc+

+6:i386, libc6-dev-i386, lib32z1, lib32ncurses5, lib32bz2-1.0, and libpng12

libraries.

Note: • For Ubuntu 18.04, additionally install libqt5xml5 and liblzma-dev libraries.


Once done, reinstall Quartus Prime. You may need to refer to document below related to 

Intel® FPGA Software Installation and Licensing

https://www.intel.com/content/dam/www/programmable/us/en/pdfs/literature/manual/quartus_install.pdf


Then make sure the device .qdz file is in same directory with Quartus installer. Install the device support.



0 Kudos
SyafieqS
Moderator
1,847 Views

Hi Qazi,


From your link given, I can see you are struggling with Quartus and device installation. Please make sure all the installation is good. By default there should not be a blank. Refer to the document below related to Intel® FPGA Software Installation and Licensing.

https://www.intel.com/content/dam/www/programmable/us/en/pdfs/literature/manual/quartus_install.pdf


Regards




0 Kudos
Qazi_Shahid
New Contributor I
1,832 Views

I have uninstalled the software and installed the libraries suggested (Although I found that all those were already installed).

But even after that when I reinstalled the software the problem is still exist.

 

They software is still asking for licenses everytime I open it and then ask to installed any device. but during installing the cyclone V device it again gives that error that

 

"error reading INI file".

 

0 Kudos
Qazi_Shahid
New Contributor I
1,824 Views

Also where is this INI file located. I didn't found in any location.

I had seen somewhere on web that it should be in .alter.quartus but this directory only contains quartus2.qreg file.

0 Kudos
SyafieqS
Moderator
1,786 Views

Hi Qazi,


Is your issue still persist? I sent you an email please take a look at it.


Thanks,

Regards


0 Kudos
Qazi_Shahid
New Contributor I
1,753 Views

@SyafieqS  I have replied to your mail last week but after that I haven't heard from you.

 

Kindly let me know if you haven't received the mail.

 

 

0 Kudos
SyafieqS
Moderator
1,742 Views

Hi Qazi,


I have not received any email from you, Can you try to reply to the email (I will send another one).


0 Kudos
Qazi_Shahid
New Contributor I
1,732 Views

@SyafieqS I have replied to mail agian. Let me know if haven't recieved it.

0 Kudos
SyafieqS
Moderator
1,689 Views

Hi Qazi,


Still cant see the email. Can you check your private message?


Reply