Intel® High Level Design
Support for Intel® High Level Synthesis Compiler, DSP Builder, OneAPI for Intel® FPGAs, Intel® FPGA SDK for OpenCL™
655 Discussions

Local management Interface for Arria 10 PCIe Hard IP

sgr
Beginner
1,382 Views

Hi,

I want to configure the Root Port Configuration space register via the Local management interface.

But I am not sure how to enable the LMI interface.

And One more question is the data width of these registers are 32-bit registers but here only 8 bits are allowed in LMI, So how to configure these registers through LMI

 

So ,Please Get me back as soon as possible

Thanks

0 Kudos
1 Solution
wchiah
Employee
1,306 Views

Hi,


I wish to follow up with you about this case.

Do you have any further questions on this matter ?

​​​​​​​Else I would like to have your permission to close this forum ticket


Regards,

Wincent_Intel


View solution in original post

0 Kudos
10 Replies
wchiah
Employee
1,352 Views

Hi,


Thank you for reaching out.

Just to let you know that Intel has received your support request and I am assigned to work on it.

Allow me some time to look into your issue. I shall come back to you with findings.


Thank you for your patience.


Best regards,

Wincent_Intel


0 Kudos
wchiah
Employee
1,346 Views

Hi,

 

For enable the LMI interface you can refer user guide at link below

https://www.intel.com/content/www/us/en/docs/programmable/683647/18-0/lmi-signals.html

May I know you are using AVST or AVMM ? 

Regards,

Wincent_Intel

0 Kudos
sgr
Beginner
1,345 Views

It is Avalon Stream Interface

0 Kudos
wchiah
Employee
1,343 Views

Hi Sgr,

Glad that I am sending correct document for you on AVST LMI signal.
Feel free to get back to me if you need any further clarification.

 

Regards.

Wincent_Intel

0 Kudos
wchiah
Employee
1,327 Views

Hi,

 

Hope below picture clarified on how to enabling LMI in AVST, Arria 10

wchiah_0-1663117032958.png

Regards,
Wincent_Intel

0 Kudos
wchiah
Employee
1,307 Views

Hi,


I wish to follow up with you about this case.

Do you have any further questions on this matter ?

​​​​​​​Else I would like to have your permission to close this forum ticket


Regards,

Wincent_Intel


0 Kudos
sgr
Beginner
1,299 Views

Hi Wincent_Intel,

Thank you for your support.

I am facing one issue while creating the BSP project in Quartus version 21.3, I am not able to create the project.

Capture_bsp.PNG

Would you please guide me on this

0 Kudos
wchiah
Employee
1,295 Views

Hi,

 

I saw similar issue happen before, you can check the KnowledgeBased below

You can try the step at link below

https://www.intel.com/content/www/us/en/support/programmable/articles/000090071.html

If your problem still not solve you may try the second method

https://community.intel.com/t5/Nios-II-Embedded-Design-Suite/failed-to-execute-wsl-dos2unix-create-this-bsp/m-p/1344838

 

Hope this answer your question

Regards,

Wincent_Intel

0 Kudos
wchiah
Employee
1,253 Views

Hi,


I wish to follow up with you about this case.

Do you have any further questions on this matter ?

​​​​​​​Else I would like to have your permission to close this forum ticket


Regards,

Wincent_Intel


0 Kudos
wchiah
Employee
1,244 Views

Hi,

 

I strongly believe my previous reply answered your question. 

We do not receive any response from you to the previous answer that I provided.

This thread will be transitioned to community support.

If you have a new question, feel free to open a new thread to get support from Intel experts.

Otherwise, the community users will continue to help you on this thread. Thank you

If you feel your support experience was less than a 9 or 10,

please allow me to correct it before closing or please let me know the cause so that I may improve your future support experience.

 

Regards,

Wincent_Intel


0 Kudos
Reply