Ethernet issue:TSE_MAC_INIT error"

BPani1 · ‎01-31-2019

Hi ,

We are using quartus prime -18.1 version software.while executing sample ethernet application on Arria 10 GX EVM(Serial Number:10PCIe0002691) using NIOS SBT, its giving error like: "TSE_MAC_INIT error".

while I have gone through the code: its getting failed in alt_msgdma_prefetcher_add_standard_desc_to_list function which is getting called by msgdma_read_init() function.

I have attached the software code also.

Console log:

InterNiche Portable TCP/IP, v3.1

altera_eth_tse_init 0

prep_tse_mac 0

Inside get_mac_addr

Inside get_ip_addr function

Static IP Address is 192.168.5.4

prepped 1 interface, initializing...

tse_mac_init 0

List of PHY profiles supported (Total profiles = 5)...

Profile No. 0 :

PHY Name : Marvell 88E1111

PHY OUI : 0x005043

PHY Model Num. : 0x0c

PHY Rev. Num. : 0x02

Status Register : 0x11

Speed Bit : 14

Duplex Bit : 13

Link Bit : 10

Profile No. 1 :

PHY Name : Marvell Quad PHY 88E1145

PHY OUI : 0x005043

PHY Model Num. : 0x0d

PHY Rev. Num. : 0x02

Status Register : 0x11

Speed Bit : 14

Duplex Bit : 13

Link Bit : 10

Profile No. 2 :

PHY Name : National DP83865

PHY OUI : 0x080017

PHY Model Num. : 0x07

PHY Rev. Num. : 0x0a

Status Register : 0x11

Speed Bit : 3

Duplex Bit : 1

Link Bit : 2

Profile No. 3 :

PHY Name : National DP83848C

PHY OUI : 0x080017

PHY Model Num. : 0x09

PHY Rev. Num. : 0x00

Status Register : 0x00

Speed Bit : 0

Duplex Bit : 0

Link Bit : 0

Profile No. 4 :

PHY Name : Intel PEF7071

PHY OUI : 0x355969

PHY Model Num. : 0x00

PHY Rev. Num. : 0x01

Status Register : 0x00

Speed Bit : 0

Duplex Bit : 0

Link Bit : 0

INFO : TSE MAC 0 found at address 0x00003000

INFO : Multi Channel = No

INFO : MDIO Shared = No

INFO : MAC Type = 10/100/1000 Ethernet MAC

INFO : PCS Enable = Yes

INFO : PCS SGMII Enable = Yes

INFO : MAC Address = 0x00003000

INFO : MAC Device = tse_mac_device[0]

INFO : PHY Marvell 88E1111 found at PHY address 0x00 of MAC Group[0]

INFO : PHY OUI = 0x005043

INFO : PHY Model Number = 0x0c

INFO : PHY Revision Number = 0x2

INFO : PHY[0.0] - Automatically mapped to tse_mac_device[0]

INFO : PHY[0.0] - Advertisement of 1000 Base-T Full Duplex set to 1

Created "Inet main" task (Prio: 2)

INFO : PHY[0.0] - Advertisement of 1000 Base-T Half Duplex set to 1

INFO : PHY[0.0] - Advertisement of 100 Base-T4 set to 0

INFO : PHY[0.0] - Advertisement of 100 Base-TX Full Duplex set to 1

INFO : PHY[0.0] - Advertisement of 100 Base-TX Half Duplex set to 1

INFO : PHY[0.0] - Advertisement of 10 Base-TX Full Duplex set to 1

INFO : PHY[0.0] - Advertisement of 10 Base-TX Half Duplex set to 1

INFO : PHY[0.0] - Restart Auto-Negotiation, checking PHY link...

Created "clock tick" task (Prio: 3)

i value is 0

INFO : PHY[0.0] - Auto-Negotiation PASSED

INFO : Applying additional PHY configuration of Marvell 88E1111

INFO : PCS[0.0] - Configuring PCS operating mode

INFO : PCS[0.0] - PCS SGMII mode enabled

INFO : PHY[0.0] - Checking link...

INFO : PHY[0.0] - Link established

INFO : PHY[0.0] - Speed = 1000, Duplex = Full

OK, x=0, CMD_CONFIG=0x00000000

MAC post-initialization: CMD_CONFIG=0x0400020b

TSE_MAC_INIT error

init error -1 on net[0]

mctest init called

IP address of : 0.0.0.0

Simple Socket Server starting up

Deshi_Intel · ‎02-01-2019

Hi Biswajit Panigrahi, Just curious is the failure encountered on your own design or Intel FPGA reference design ? If it's reference design then which design is it ? And also which board that you run the test ? your own board or some dev kit board from Intel FPGA ? Thanks. Regards, dlim