Intel® Quartus® Prime Software
Intel® Quartus® Prime Design Software, Design Entry, Synthesis, Simulation, Verification, Timing Analysis, System Design (Platform Designer, formerly Qsys)
16908 Discussions

support for Agilex SoC Dev Kit DK-SI-AGI027FB in Quartus Prime Pro

WWood7
Beginner
1,723 Views

The Agilex 7 I-series Board DK-SI-AGI027FB is not listed as a supported board in Quartus Prime Pro 23.2 nor in the Platform Developer. Is there any plan to support this board? (It was expensive enough...) There is support for the RES version of the board, but it has a different FPGA part. Thank you.

Labels (1)
0 Kudos
1 Solution
Farabi
Employee
1,475 Views

Hello, 

 

The board you are using now is not in the board compilation list, however you can still compile if you select the exact part number of the device you have on the board. Currently the board you are using is not available from the selection list, however, it will be available in future Quartus version. The only benefit if you have board selection in the compilation setting is the pin assign will be set as the board pin assignment. 

 

Board selection:

board_selection.png

 

Device Selection:

device_selection.png

If you have selected the correct part number as above, your compilation will run correctly, and it can be uploaded into the device on your devkit without any problem. 

 

For current situation, we can't do anything to enable the DK-SI-AGI027FB board in the board selection list, until it is available in future Quartus version. 

 

regards,

Farabi

View solution in original post

0 Kudos
13 Replies
IntelSupport
Community Manager
1,675 Views

Hello,

Good day

 

Thank you for using Intel Premier Support. I'm Elina looking into your issue and allow me some time to look into your issue. I shall come back to you with findings.

 

Thank you for your patience.

 

Best Regards,

Elina


0 Kudos
IntelSupport
Community Manager
1,647 Views

Hello,

 

I'm still in the midst of the discussion regarding this with the internal teams. Unfortunately, it takes longer than usual heard. I will plan on letting you know as soon as I learn more information. Really appreciate your patience.

 

Warm Regards,

Elina


0 Kudos
WWood7
Beginner
1,637 Views

OK, thank you!

0 Kudos
IntelSupport
Community Manager
1,568 Views

Hi

Good day,


Sorry for taking long time to reply. After discussion with my internal team, you may follow step like below :

1) Go to this link : https://www.intel.com/content/www/us/en/products/details/fpga/development-kits/agilex/si-agi027.html


2) Download DK-SI-AGI027FB( v23.1 or higher)


3) After finish download folder , may open golden top folder. The .qsf here will have all the FPGA pin connections as on dev kit. Use as required. Remove/comment rest of the pins. :



select below screenshot that i attached for your references:



Thank you


Regards

ELINA


0 Kudos
WWood7
Beginner
1,553 Views

Thank you for the information.  I have already taken those steps, and although my code does compile and load, I wasn't sure everything was correct.

I wonder if you could repost the screenshots? I cannot view them. (I am using the Chrome browser, version 116.0.5845.141. Should I use another?)

Best wishes,

Bill W

0 Kudos
IntelSupport
Community Manager
1,537 Views

Hi

Good Day,


I have sent my previous replied through your email. Please check .


Thank you


Regards

ELINA


0 Kudos
Elina_Intel
Employee
1,533 Views

Hi

Below here i try repost my previous replied :

 

1) Go to this link : https://www.intel.com/content/www/us/en/products/details/fpga/development-kits/agilex/si-agi027.html

 

2) Download DK-SI-AGI027FB( v23.1 or higher) from Table 3 Documentation

Elina_Intel_0-1693972046552.png

 

 

3) After finish download folder , may open golden top folder. The .qsf here will have all the FPGA pin connections as on dev kit. Use as required. Remove/comment rest of the pins. :

 

Elina_Intel_1-1693972046555.png

 

 

 below screenshot that i attached for your references:

 

Elina_Intel_2-1693972046566.png

 

 

Elina_Intel_3-1693972046576.png

 

 

Thank you

Regards

ELINA

0 Kudos
WWood7
Beginner
1,514 Views

Dear Elina,

 

Thank you! I can see the images and I received your e-mail with the same information.

 

The device I have is AGIB027R31B1E1VAA. This is not the same device as the one you list. This is why I initially posted my question. It appears that Quartus supports the DK-SI-AGI027FES board. I have the DK-SI-AGI027FB board.  Are all settings are the same on the two boards? 

 

Best wishes,

 

Bill W.

0 Kudos
Elina_Intel
Employee
1,497 Views

Hi Bill W., 

Is this device that you have? would like to get your confirmation. It seem like it does have in Quartus Prime Pro Edition for AGIB027R31B1E1VAA.

Elina_Intel_0-1694015048507.png

 

Thank You 

 

ELINA

 

0 Kudos
WWood7
Beginner
1,489 Views

Yes, that is right. I know that Quartus has that and that is what I am using. I am asking about the supported board(s). If you look at your other screenshot, the one with the "Board" tab open, you will see in the "device" column that a different FPGA part is listed. I believe that it is a different version of the board that I have.

Thank you. I am sorry for all the questions.

0 Kudos
Farabi
Employee
1,476 Views

Hello, 

 

The board you are using now is not in the board compilation list, however you can still compile if you select the exact part number of the device you have on the board. Currently the board you are using is not available from the selection list, however, it will be available in future Quartus version. The only benefit if you have board selection in the compilation setting is the pin assign will be set as the board pin assignment. 

 

Board selection:

board_selection.png

 

Device Selection:

device_selection.png

If you have selected the correct part number as above, your compilation will run correctly, and it can be uploaded into the device on your devkit without any problem. 

 

For current situation, we can't do anything to enable the DK-SI-AGI027FB board in the board selection list, until it is available in future Quartus version. 

 

regards,

Farabi

0 Kudos
WWood7
Beginner
1,440 Views

Thank you both!

0 Kudos
Reply