Nios® II Embedded Design Suite (EDS)
Support for Embedded Development Tools, Processors (SoCs and Nios® II processor), Embedded Development Suites (EDSs), Boot and Configuration, Operating Systems, C and C++
Announcements
Intel Support hours are Monday-Fridays, 8am-5pm PST, except Holidays. Thanks to our community members who provide support during our down time or before we get to your questions. We appreciate you!

Need Forum Guidance? Click here
Search our FPGA Knowledge Articles here.
12453 Discussions

Fail to generate a boot loader with QSPI Flash

GSite
Novice
1,868 Views

I tried a lot of ways to download uboot to QSPI FLASH through the directive of quartus_hps. However, there will be errors.

Error:Not able to halt CPU 0

Error:Fail to write 1 of DWORD(s) to address 0xFFD13000 through CPU 0

Error:Fail to set non-secure transcation for register 0xFFD13000

What should I do?

6 Replies
AnandRaj_S_Intel
Employee
1,016 Views

Hi,

 

Refer the link below which may help in debug

https://www.youtube.com/watch?v=5qxyEaO8C5o

https://rocketboards.org/foswiki/Documentation/GSRD131QspiProgram

 

Best Regards,

Anand Raj Shankar

(This message was posted on behalf of Intel Corporation)

 

GSite
Novice
1,016 Views

​Thanks for your reply,I have learned the tutorial refer to https://rocketboards.org/foswiki/Documentation/A10Gsrd170QspiBoot

but I did not solve this problem.I designed a board using ARRIA10 SOC.When I download uboot to QSPI FLASH,The error information is shown in the figure1.Then I debug bootloader using ARM DS-5.The error information is shown in the figure2. What should I do? 

1.PNG2.PNG

GSite
Novice
1,016 Views
​Thanks for your reply,I have learned the tutorial refer to https://rocketboards.org/foswiki/Documentation/A10Gsrd170QspiBoot but I did not solve this problem.I designed a board using ARRIA10 SOC.When I download uboot to QSPI FLASH,The error information is shown in the figure1.Then I debug bootloader using ARM DS-5.The error information is shown in the figure2. What should I do? 2018年10月30日 祝好! 郭玥 On 10/30/2018 16:52,Intel Forums<supportreplies@intel.com> wrote: Hi, Refer the link below which may help in debug https://www.youtube.com/watch?v=5qxyEaO8C5o https://rocketboards.org/foswiki/Documentation/GSRD131QspiProgram Best Regards, Anand Raj Shankar (This message was posted on behalf of Intel Corporation) Anand Raj Shankar (Intel) Hi, Refer the link below which may help in debug https://www.youtube.com/watch?v=5qxyEaO8C5o https://rocketboards.org/foswiki/Documentation/GSRD131QspiProgram Best Regards, Anand Raj Shankar (This message was posted on behalf of Intel Corporation) or reply to this email Original post GSite (Customer) asked a question. Saturday, 2018年10月27日 AM10:06 Fail to generate a boot loader with QSPI Flash I tried a lot of ways to download uboot to QSPI FLASH through the directive of quartus_hps. However, there will be errors. Error:Not able to halt CPU 0 Error:Fail to write 1 of DWORD(s) to address 0xFFD13000 through CPU 0 Error:Fail to set non-secure transcation for register 0xFFD13000 What should I do? Anand Raj Shankar (Intel) Hi, Refer the link below which may help in debug https://www.youtube.com/watch?v=5qxyEaO8C5o https://rocketboards.org/foswiki/Documentation/GSRD131QspiProgram Best Regards, Anand Raj Shankar (This message was posted on behalf of Intel Corporation) Tuesday, 2018年10月30日 PM4:52 You're receiving emails when someone "Comments on my posts." To change or turn off Forums email, log in as 300001501521@intel.com.isvc. Are notifications about this post getting annoying? Reply to this email with the word " mute ". For Privacy and Legal notices, please visit these links: http://www.intel.com/privacy, https://www.intel.com/content/www/us/en/legal/terms-of-use.html.
AKb
Beginner
1,016 Views

have u selected the correct msel settings to boot from qspi?

 

gbuskirk
Beginner
756 Views

Were you able to make any progress on this?  I'm getting the very same responses, trying to load U-Boot to a QSPI device with quartus_hps.  The FPGA has configured properly from it's own QSPI device.  The HPS has its QSPI device where U-Boot should load from.  I have confirmed BSEL is pulled up and down to BSEL[2:0] = 0x6 (1.8V QSPI).

gbuskirk
Beginner
697 Views

First, confirm that you have pullup resistors (1KOhm) to 1.8VDC (VDD_IO) on HPS_nPOR and HPS_nRST pins.

Reply