FPGA Intellectual Property
PCI Express*, Networking and Connectivity, Memory Interfaces, DSP IP, and Video IP
6343 Discussions

EMIF ip fetches error while simulating in vcs

DChak3
Beginner
839 Views

I tried to simulate the emif IP, but it shows below error:

227213 ns: ERROR: iossm_bf_cpu_cpu_test_bench/ihp_read is 'x'

$stop at time 227212598000 Scope: unex_block_design.emif_s10_0.emif_s10_0.arch.arch_inst.io_ssm_inst.io_ssm.inst.PROTECTED File: PROTECTED Line: 0

 

i used vcs 2019 sp2

generated for device 1SD280PT2F55E2VGS1 from quartus 19.4

steps used :

1.generated the default IP

2.go to sim folder>synopsys vcs

3.run command sh vcs_setup.sh

0 Kudos
7 Replies
NurAida_A_Intel
Employee
677 Views

Dear DChak3,

 

Thank you for joining this Intel Community.

 

I believed your design contain Intel® Stratix® 10 HPS EMIF thus you will see this error is generated. It is a known issue as Stratix 10 HPS EMIF simulation is not supported.

 

You may refer to this KDB link for more details -->

https://www.intel.com/content/www/us/en/programmable/support/support-resources/knowledge-base/emif/2018/error--iossm_bf_cpucputestbench-ihpread-is--x-.html

 

Thanks

 

Regards,

Aida

 

 

0 Kudos
DChak3
Beginner
677 Views

Hi nuraidaA

 

I am not using Intel® Stratix® 10 HPS EMIF instead I am using External Memory Interfaces Intel stratix 10 FPGA IP. It is simulating if I am using this IP with other bunch of IP's. But while I was trying to create libraries using the script provided by quartus. When i select the option from tools>Generate simulator script for IP.

 

I ran the script and it shows error mentioned above when it reaches to simulate EMIF IP.

 

Reference snapshot attached. The blue circled one is used in the design.

 

 

 

emif_IP_snapshot.PNG

0 Kudos
NurAida_A_Intel
Employee
677 Views

Hi,

 

I did internal searching and found that the simulation tools supported for VCS Quartus version 19.4 is O-2018.09-SP2-2 (64-bit Linux only).

 

Can you try to swicth to vcs 2018 sp2 and see if the error still replicate ?

 

Regards,

Aida

0 Kudos
alinave
Beginner
677 Views

Hi Aida,

 

I see the same problem while simulating the EMIF design which does not contain the HPS core. I am using xcelium2019.09_s007 and here is the error I see during configuration:

170038 ns: ERROR: iossm_bf_cpu_cpu_test_bench/ihp_read is 'x'

Simulation stopped via $stop(1) at time 170037750 PS + 3

xcelium> exit

 

Can you help with this?

 

Thanks,

Naved

0 Kudos
alinave
Beginner
677 Views

PS: The device is Stratix 10 GX which anyway does not have HPS and the Quartus version is 19.4.

 

0 Kudos
NurAida_A_Intel
Employee
677 Views

Hi @alinave​ ,

 

Sincerely sorry for the delay due to long holiday in my region.

 

Have you try to used this supported tools version for Xcelium for Quartus 19.4?

xcelium.PNG

Regards,

Aida

0 Kudos
NurAida_A_Intel
Employee
677 Views

Also may I know which memory simulation model are you using (for example Micron or etc)?

 

 

 

 

0 Kudos
Reply