Programs compiled with ifx are slower than compiled with ifort.

[eliopoulos]

Programs compiled with ifx are slower than compiled with ifort. Is this going to change with the future updates? Speed is very important to me and now ifort has been discontinued.

[Ron_Green]

Perhaps you can share the compiler options you used, and the Intel processor you are targeting with -x or -ax, and if you can, share the sources.

[eliopoulos]

I don't know where to find the compiler options you need. I use two different Intel processors: core i9 14900ks and core i7 1260p. I don't understand the -x and -ax thing. I compile from the Visual Studio Community 2022. I don't want to share the program in public but I could send it with e-mail.

[Ron_Green]

You can look in Project Properties for your Release Configuration and x64 configuration.  The processor targeting will look like this:

[eliopoulos]

This is what I use:

[eliopoulos]

Is there anything I can do to accelerate my programs compiled with ifx?

[Mark_Lewy]

Without knowing your compiler options, it's difficult to say what might be causing this.  I suggest you share the Fortran command line from the project properties.  For example,

One thing I noted, when we ported to ifx,  was that if you use /standard-semantics it degrades floating point performance significantly with IFX because it sets /assume:ieee_compares.  You could (like us) add /assume:noieee_compares as an additional option.

Our application generally runs faster or at similar speeds to ifort when built with ifx, depending on workload.

Also, check out the porting guide from ifort to ifx: Porting Guide for ifort Users to ifx and see if anything in there helps.

[eliopoulos]

My compiler options:

I tried to add /assume:noieee_compares and the program remains slower than compiled with ifort.

[Mark_Lewy]

Nothing obvious stands out here.  I'd suggest profiling your program with vTune to see where the hotspots are.

[Ron_Green]

What you showed does not match the recommendation I had for using -x or -ax options.  This is called out in the Porting Guide

https://www.intel.com/content/www/us/en/developer/articles/guide/porting-guide-for-ifort-to-ifx.html

under the section on CPU performance:

-O2 Add -x<code> to enable all available Intel optimizations and advanced vectorization. Add -xHost to enable those optimizations the platform where you are compiling.

O2 is NOT enough for ifx.  It was for ifort.  With ifx, you only get Intel proprietary optimizations IF you include -xhost or -x<arch> or -ax equivalents.  

This is something I am hearing from customers.  They got used to simply using O2 with ifort and are unaware that they have to use O2 and -x<something> with ifx.  I recommend -O2 -xhost.  Try that.

[eliopoulos]

How can I set: -O2 -xhost?

[Ron_Green]

O2 will be set by using Release Configuration.  Here is where to find setting /Qxhost

[eliopoulos]

ifort remains 20-30% faster.

[Ron_Green]

Is it possible for you to Clean the project, then zip up the entire solution directory and attach it here? 

One other question - is the primary data type REAL, REAL (kind=8), or COMPLEX ?

[eliopoulos]

The primary data type is double precision.

[Ron_Green]

Thanks for the files.  But nlay.txt is zero length and it causes the program to exit (end of file during read).  Can you attach a good nlay.txt file?  

[eliopoulos]

Here it is.

[eliopoulos]

Any news?

[TobiasK]

@eliopoulos thanks for sharing the code. However, your code is quite complex and it will take a while for us to figure out where something is going wrong. If you have purchased priority support, we will treat this with higher priority, but I don't see an entry for you. If you can extract smaller code samples the process on our side is also a lot faster. You may start with Vtune to compare the binaries generated with IFORT/IFX and see where the performance drop comes from. If you need help with Vtune, please ask here:
https://community.intel.com/t5/Analyzers/bd-p/analyzers

[Ron_Green]

@eliopoulos I will get to this issue today.  There was a US Holiday Thursday and Friday.  Monday I have been catching up on backlog.

[Ron_Green]

I need ALL the .txt files.  Here is a list from the code - are there others missing? 

open(2,file='laminate.txt')
do i=1,nl
read(2,*)mat(i),thick(i),angled(i)
enddo
close(2)

do i=1,nl
angle(i)=angled(i)*pi/180.0d0
enddo

zk(1)=-sum(thick)/2.0d0+thick(1)/2.0d0
if (nl>1) then
do i=1,nl-1
zk(i+1)=zk(i)+thick(i)/2.0d0+thick(i+1)/2.0d0
enddo
else
endif

open(3,file='Nx.txt')
read(3,*)FtNx
close(3)

open(4,file='Ny.txt')
read(4,*)FtNy
close(4)

open(5,file='Ns.txt')
read(5,*)FtNs
close(5)

open(6,file='Mx.txt')
read(6,*)FtMx
close(6)

open(7,file='My.txt')
read(7,*)FtMy
close(7)

open(8,file='Ms.txt')
read(8,*)FtMs
close(8)