Intel® Quartus® Prime Software
Intel® Quartus® Prime Design Software, Design Entry, Synthesis, Simulation, Verification, Timing Analysis, System Design (Platform Designer, formerly Qsys)
16593 Discussions

Quartus 21.1 and Blaster 1

Bop
Novice
959 Views
Hello All,
 

At the Moment I`m working with "Quartus 21.1 and Blaster 1", when starting download of the *.pof file, with selected Terasic Blaster 1 USB after 4% an error appears. 

With the same cabeling and hardware, Quartus 18.0 works for me?

 

LOG:

Info (209060): Started Programmer operation at Mon Jan 29 08:48:54 2024
Info (209017): Device 1 contains JTAG ID code 0x031810DD
Info (209060): Started Programmer operation at Mon Jan 29 08:48:54 2024
Info (209016): Configuring device index 1
Info (209017): Device 1 contains JTAG ID code 0x031810DD
Info (209007): Configuration succeeded -- 1 device(s) configured
Info (209011): Successfully performed operation(s)
Info (209061): Ended Programmer operation at Mon Jan 29 08:48:55 2024
Info (209024): Programming device 1
Error (209012): Operation failed <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<This
Info (209061): Ended Programmer operation at Mon Jan 29 08:49:18 2024

 

Any ideas?

Thanks

Bop

Labels (1)
0 Kudos
10 Replies
NurAiman_M_Intel
Employee
918 Views

Hi,


-Have you also try with Quartus v23.1? Does it work?

-What type of Quartus did you used? Standard?

-What is the device used?

-Can you try to compile a simple design and download a pof file using Quartus 21.0? Does it work?


Regards,

Aiman


0 Kudos
Bop
Novice
911 Views

Hi Aiman, 

Thanks for responding that fast. 

I ll try the 23.1. 

I use Quartus (Quartus Prime 21.1) Lite Edition.

The final device is a Motor Controller. 

U will here from me. 

Regards, Patrick

 

0 Kudos
Bop
Novice
891 Views

Hi  Aiman, 

unfortunately 23.1 Lite has the same issue with the Blaster 1. Blaster 2 is ordered for further Tests. 

 

--> Info (209060): Started Programmer operation at Wed Jan 31 14:29:36 2024
Info (209017): Device 1 contains JTAG ID code 0x031810DD
Info (209060): Started Programmer operation at Wed Jan 31 14:29:37 2024
Info (209016): Configuring device index 1
Info (209017): Device 1 contains JTAG ID code 0x031810DD
Info (209007): Configuration succeeded -- 1 device(s) configured
Info (209011): Successfully performed operation(s)
Info (209061): Ended Programmer operation at Wed Jan 31 14:29:38 2024
Info (209024): Programming device 1
Error (209012): Operation failed
Info (209061): Ended Programmer operation at Wed Jan 31 14:30:01 2024

 

Regards, Patrick

0 Kudos
FvM
Valued Contributor III
864 Views
I would compare programmer options of both Quartus installations. Under circumstances it is necessary to disable the on-chip configuration controller during programming.
Which is the involved device, is it MAX10?
0 Kudos
Bop
Novice
844 Views

Hi, thanks I'll test that.

Yes, it's about 10M02SCE144.

 

Regards, Patrick

0 Kudos
Bop
Novice
804 Views

Hi Aiman, 

Quartus 18.0 and Quartus 23.1 have the same settings. 

The "Enable real-chip configuration controller" was allready disabled. 

 

Bop_2-1706855856393.png

 

 

Do you have further suggestions?

 

Regards Patrick

0 Kudos
Bop
Novice
804 Views

cancled

0 Kudos
NurAiman_M_Intel
Employee
715 Views

Hi Patrick,


While looking for the root cause of your problem, I found below KDB that highlight the same error:


https://www.intel.com/content/www/us/en/support/programmable/articles/000092639.html


We suggest you to use Quartus 19.1 and below for now. Please refer to KDB above.


Regards,

Aiman


Bop
Novice
703 Views

Hi Aiman, 

Thanks for that. This solution works for me with the Blaster 1 and Blaster 2.

Greetings Patrick

0 Kudos
NurAiman_M_Intel
Employee
682 Views

I’m glad that your question has been addressed, I now transition this thread to community support. If you have a new question, feel free to open a new thread to get the support from Intel experts. Otherwise, the community users will continue to help you on this thread. Thank you.


0 Kudos
Reply