- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have a Intel Quick Assist Adapter 8950-SCCP (dh895xcc).
I can not find it's driver in intel site.
Intel® QuickAssist Technology Driver for Linux* – HW Version 1.X
Intel® QuickAssist Adapter Family for Servers
Can anyone give me some hint? thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Huang1,
If QAT install was performed with intel_iommu=on and ./configure targeting PF use only:
This particular configuration is not valid since PFs are not able to be used when IOMMU is enabled.
Please refer to the following website for cpa_sample_code details:
https://intel.github.io/quickassist/GSG/2.X/sampleapplications.html#performance-sample-code
Note: Before running cpa_sample_code make sure QAT is properly configured, refer to: https://intel.github.io/quickassist/GSG/2.X/installation.html
Regards,
Ronny G
Link Copied
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Huang1,
You may want to use the following driver: https://www.intel.com/content/www/us/en/download/19734/intel-quickassist-technology-driver-for-linux-hw-version-1-x.html
This driver should also work for DH8925, DH8926, DH8950 and DH8955.
There is more information available here: https://ark.intel.com/content/www/us/en/ark/products/codename/60172/products-formerly-coleto-creek.html please be aware that this product has been discontinued.
Regards,
Ronny G
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Ronny,
Thanks your kindly support on QAT 8950.
I did this on ubuntu 2204, no error appears.
|
And list it
#lspci -s 0b:00.0 -v 0b:00.0 Co-processor: Intel Corporation DH895XCC Series QAT Subsystem: Intel Corporation DH895XCC Series QAT Flags: bus master, fast devsel, latency 0, IRQ 40, IOMMU group 26 Memory at ea100000 (64-bit, prefetchable) [size=512K] Memory at fcb40000 (64-bit, non-prefetchable) [size=256K] Memory at fcb00000 (64-bit, non-prefetchable) [size=256K] Capabilities: [b0] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [60] MSI-X: Enable+ Count=33 Masked- Capabilities: [6c] Power Management version 3 Capabilities: [74] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [138] Alternative Routing-ID Interpretation (ARI) Capabilities: [140] Single Root I/O Virtualization (SR-IOV) Kernel driver in use: dh895xcc Kernel modules: qat_dh895xcc |
#lsmod | grep qat |
#systemctl status qat_service.service 6月 12 20:18:31 jinhua-x570 systemd[1]: Starting LSB: modprobe the QAT modules, which loads dependant modules, before calling the user space utility to pass configuration parameters...
|
But, when I run the sample code, there is error.
#./build/cpa_sample_code [error] do_userStart() - : Failed to start services /opt/qat/QAT.L.4.25.0-00001/quickassist/lookaside/access_layer/src/sample_code/performance/cpa_sample_code_main.c, main():486 Could not start sal for user space |
Could you give me more advice on this? thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Huang1,
Are you enabling sriov? I dont think you are, you are using: ./configure --enable-icp-debug -enable-icp-log-syslog --enable-icp-dc-return-counters-on-error
This error usually happends when QAT install was performed with intel_iommu=on and ./configure --enable-icp-sriov=host – verify vfs are running:
To start vfs enter: # service qat_service_vfs start
To verify vfs are running enter: # service qat_service_vfs status
If QAT install was performed with intel_iommu=on and ./configure targeting PF use only:
This particular configuration is not valid since PFs are not able to be used when IOMMU is enabled.
Regards,
Ronny G
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Ronny G,
I did not enable sriov and set intel_iommu=on in ./configure step.
Actually I want to invest compression things on QAT 8950.
Could you help me on configure it correctly? Thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Huang1,
If QAT install was performed with intel_iommu=on and ./configure targeting PF use only:
This particular configuration is not valid since PFs are not able to be used when IOMMU is enabled.
Please refer to the following website for cpa_sample_code details:
https://intel.github.io/quickassist/GSG/2.X/sampleapplications.html#performance-sample-code
Note: Before running cpa_sample_code make sure QAT is properly configured, refer to: https://intel.github.io/quickassist/GSG/2.X/installation.html
Regards,
Ronny G
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Ronny_G,
Thanks your kindly help.
I performance the test on a Intel CPU (Intel(R) Core(TM) i7-8700K CPU @ 3.70GHz) (previously on a AMD).
Configured as:
./configure --enable-icp-debug --enable-icp-dc-return-counters-on-error --enable-icp-dc-only
The samples_code works:
... Inst 0, Affin: 0, Dev: 0, Accel 0, EE 0, BDF 03:00:00 Sample code completed successfully. |
Thank you very much on QAT env setup.
I will invest on compression test.
This ticket can be closed. I will raise new if having problem on compression test.
![](/skins/images/C4F7392A5C68ACA60290C9576F107044/responsive_peak/images/icon_anonymous_message.png)
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page