- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have been using the VTune Amplifier XE 2016 for Linux to test some applications with our Celeron J1900 chip. When I run the general exploration test, the whole system freezes permanently forcing me to power cycle the system. Other tests seem to work fine.
Any ideas on what could be happening? Are there logs I can check?
Link Copied
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Did you mean that you can run advanced-hotspots on same platform without problem? Celeron J1900 is Bay Trail architecture, are you sure that you work in last VTune(TM) Amplfier XE 2016 Update 2? Use "-knob enable-stack-collection=false".
If the problem can be repeated, set "export AMPLXE_LOG_LEVEL=DEBUG" first, then rerun general-exploration, log file should be under /tmp/amplxe-log-$user. Please attach this for investigating. Thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes, I am using 2016 update 2. Advanced hotspots works every time but general exploration does not. I am using the gui, when do i run "-knob enable-stack-collection=false"?
I tried to collect logs, but when it freezes, i have to restart the whole system and then the log files are no longer in tmp.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
If you use command line, option "-knob enable-stack-collection=false" is default. Simply use - "amplxe-cl -c general-exploration -- application".
> I tried to collect logs, but when it freezes, i have to restart the whole system and then the log files are no longer in tmp.
Please try:
1) export AMPLXE_DEBUG=1
2) export AMPLXE_LOG_LEVEL=DEBUG
3) export AMPLXE_LOG_DIR=<dir>
Then, run general-exploration, can you find log in <dir>? Also, attach result directory (which is under current directory)
Also, you can try to use events of your interest to do sampling, know what supported events are:
>amplxe-cl -collect-with runsa -knob event-config=?
Then use, "amplxe-cl -collect-with runsa -knob event-config=evt1,evt2,... -- application." - can it reproduce the issue, same as general-exploration?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I apologize as I've been busy the last week.
I ran the general-exploration test a few times with logging and never saw a crash. I then tried the GE test from the GUI with logging enabled. It didn't crash the first time, but the second time i ran the test the system crashed. I attached all the logs from running this test. You can see where it crashes at the end of "amplxe-2016.03.09-14h01m27s.3483.log". When I look at the log on the machine it happened, it repeats "\00\00\00\00\00" over and over again. I'm not seeing that after I transferred the files, but everything else is the same. When it crashes, it always seems to be at the end of data collection.
It seems that it is only an issue for the GUI meaning using the command line is an acceptable workaround. It would still be nice to understand why the GUI crashes. Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Will you please check if you have option "Collect stacks" turned off when you start GE analysis from GUI?
Also, can you please add the following option to your command line version and try again without logging enabled: -data-limit=500
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@ cole b,
Can you please try suggestions from Vitaly? It seemed that GE analysis with call stack enabling failed in BayTrail platform on GUI. Was it due to resource limitation if you worked on Visual Studio*? How about running standalone VTune application? Command line for GE analysis with call stack enabled? Option "-data-limit=500" also is good option to know if no space in disk, you may use "-duration 30" to stop GE analysis, either.
If you have no time to verify above, I may close this thread after five business days (You can input new comments in future, when you have time).
My two cents are (as a workaround) :1) Use command line instead of GUI. 2) Don't run with call stack enabled if unnecessary 3) If use call stack enabled, you may change sample interval to 10ms (modify SAV) - since stack walk may take more CPU time, reduce samples. 4) Don't run sampling collection too long, use option "-duration n" or "-data-limit=n" if possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello, I have switched projects and haven't had time to look more into this. Unfortunately, our 30 day evaluation period just ended. I may come back to this if we end up using VTune.
When I ran the tests, VTune was the only program running and collect stacks was not checked. Using the command line was an acceptable work around as it collected the wanted data.
Thanks for the help! Sorry I couldn't help figure this out.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
OK. Thanks for your quick response...I am glad that you can accept command line as workaround. I look forward to see your working on VTune again in future:-)
![](/skins/images/D2683F18326913BBA0436CB7114DD569/responsive_peak/images/icon_anonymous_message.png)
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page