I was able to download the program before, but after changing the value of register 0x24, I couldn't download the program anymore. Is there any way to reset everything or remedy it
連結已複製
1. Model: i @ 122301GCP WGI210AT;
2. The system used is a PE system;
3. Purchased separately;
4. I want to configure it as fiber optic mode; Unable to communicate after successful configuration; Can you provide me with a txt document configured for fiber optic mode; I cannot configure BK in both 0x1536 mode and 0x157C mode。
5. The following is the txt document I configured. Can you help me modify it to fiber mode?
;2013-04-07
IMGVER 0.6
IMGTYPE 4 ; I210 KX without APM
;====================================================================================
; I N T E L P R O P R I E T A R Y
;COPYRIGHT (c) 1998 - 2012 BY INTEL CORPORATION. ALL RIGHTS RESERVED.
;NO PART OF THIS PROGRAM OR PUBLICATION MAY BE REPRODUCED, TRANSMITTED, TRANSCRIBED,
;STORED IN A RETRIEVAL SYSTEM, OR TRANSLATED INTO ANY LANGUAGE OR COMPUTER LANGUAGE
;IN ANY FORM OR BY ANY MEANS, ELECTRONIC, MECHANICAL, MAGNETIC, OPTICAL, CHEMICAL,
;MANUAL, OR OTHERWISE, WITHOUT THE PRIOR WRITTEN PERMISSION OF:
;INTEL CORPORATION
;2200 MISSION COLLEGE BOULEVARD
;SANTA CLARA, CALIFORNIA 95052-8119
;Autoload commands configuration file for Flashless I210.
;SYNTAX:
;=======
; The following entries are allowed in file:
; Single command record entry:
; ============================
; <Record type> <Address> = <Data> <Reset type> <Comment>
; Series of commands which must be applied in exact sequance
; ===========================================================
; Ordered_Section_Start
; <Single record entry #1>
; .
; .
; <Single record entry #N>
; Ordered_Section_End
; Pure comment line like the one you are looking at :-).
; ======================================================
; Empty line with white characters only.
; ======================================================
; where:
; <Record type> - record type:
; WALD - autoload word record
; CSRALD - CSR autoload record
; PHYALD - PHY autoload record
; <Address> - address in hexadecimal format from range:
; 0x00 - 0x2E in WALD records definition
; 0x00000 - 0x1FFFC (4 bytes alignment required) in CSRALD records definition
; 0x00 - 0x1F in PHYALD records definition
; <Data> - Data to set in hexadecimal format:
; 0x0000 - 0xFFFF in WALD and PHYALD records definition
; 0x00000000 - 0xFFFFFFFF in CSRALD records definition
; <Reset type> - describes set of reset events for which particular record data setting is to be applied:
; LPG_RST - LanPower Good Reset only
; PCIE_RST - PCIe asserted reset and all above
; SW_RST - Host software asserted device reset and all above
; <Comment> - any sequence of printable characters (including space and tab) starting with ';'
; Duplicates (records with the same value of fields: <Record type> <Address> and <Reset type>) shouldn't
; be defined outside ordered section. If both are found outside ordered section then all but the first found
; will be silently ignored by the commands parser. If one of them is defined in ordered section then its counterpart
; outside ordered section will be ignored as well.
CSRALD 0x5ba0 = 0x00001541 LPG_RST ; [Intel] Set GPAR_EN from CSR auto config.
CSRALD 0x0000 = 0x08100241 SW_RST ; [Intel] Set CTRL.SLU.
WALD 0x0a = 0x402F PCIE_RST ; [Intel] Set GPAR_EN.
WALD 0x1b = 0x3400 PCIE_RST ; [Intel] Default settings.
WALD 0x28 = 0x1C60 PCIE_RST ; [Intel] FLBAR_Size = 000
WALD 0x0d = 0x157C PCIE_RST ; [Intel] SerDes Device ID
WALD 0x21 = 0x0584 PCIE_RST ; [Intel] Default settings.
WALD 0x24 = 0x02B0 PCIE_RST ; [Intel] Link Mode = 11 (KB)
; Common Customer Configurations
; ==============================
; Subsystem Vendor ID and Subsystem ID - Uncomment the following lines and insert the values.
; WALD 0x0B = 0x0000 PCIE_RST ; Subsystem ID
; WALD 0x0C = 0x8086 PCIE_RST ; Susbsystem Vendor ID
;
; Disable IO BAR - Uncomment the following line.
; WALD 0x19 = 0x3000 PCIE_RST ; Clear IO_Sup
;
; Non-default LED Configuration - Uncomment the following lines and set the values for the LED configuration.
; WALD 0x1C = 0x0784 PCIE_RST ; LED1 Config
; WALD 0x1F = 0x0706 PCIE_RST ; LED0,2 Config
;
; Enable Power-Down Modes - Uncomment the 1st line to enable power down with the DEV_OFF_N pin.
; Uncomment the 2nd line to enable the dynamic power down mode.
; Enabling both power down modes is not permitted.
; WALD 0x1E = 0xB200 PCIE_RST ; Enable DEV_OFF Power Down
; WALD 0x1E = 0x7200 PCIE_RST ; Power Down Settings
;
; LAN Power Consumption - Uncomment the following line and insert power data to be provided in the PCIe config space.
; WALD 0x22 = 0x0000 PCIE_RST ; LAN Power Consumption
;
; Watchdog Configuration - Uncomment the following line to enable the watchdog after reset.
; WALD 0x2E = 0x9000 SW_RST ; Enable watchdog
;
Ordered_Section_Start
CSRALD 0x5B44 = 0x00FF00A8 LPG_RST ; [Intel] Set NFTS to 0xA8.
CSRALD 0x5B40 = 0x5E000090 LPG_RST ; [Intel] cont.
Ordered_Section_End
This is my schematic and optical drive module manual. How should I configure this i210?
