Embedded Intel® Core™ Processors
Communicate Intel® Core™ Hardware, Software, Firmware, Graphics Concerns

eeupdate ARM Tool

vlin10
Beginner
11,398 Views

Hi Intel Team,

Could you please provide us eeupdate ARM tool and the Usage guide.

Please send to mailto:vic_lin@asus.com vic_lin@asus.com

Thanks in advance

Best Regards

0 Kudos
24 Replies
CarlosAM_INTEL
Moderator
4,648 Views

Hello, vic918:

Thank you for contacting Intel Embedded Community.

The https://cdrdv2.intel.com/v1/dl/getContent/348742 Intel(R) Network Connections Tools document # 348742 has the Eeupdate.

It is accessible when you are logged into your Resource & Design Center (RDC) privileged account. It can be requested by filling out the https://www.intel.com/content/www/us/en/forms/design/contact-support.html RDC Account Support form.

We hope that this information may help you.

Best regards,

Carlos_A.

0 Kudos
vlin10
Beginner
4,648 Views

Hi Carlos,

In fact I already have this file https://cdrdv2.intel.com/v1/dl/getContent/348742 Intel(R) Network Connections Tools document # 348742, but there is no eeupdateARMTool inside.

Our platform is ARM base, so we cannot use https://cdrdv2.intel.com/v1/dl/getContent/348742 Intel(R) Network Connections Tools document # 348742 to flash MAC address.

Could you please provide us eeupdateARMtool source code ?

Best Regards,

Vic

0 Kudos
CarlosAM_INTEL
Moderator
4,644 Views

Hello, vic918 :

Thanks for your reply.

In order to help you, we will contact you via email.

Best regards,

Carlos_A.

0 Kudos
vlin10
Beginner
4,644 Views

Hi Carlos,

Thanks for your help. I already receive eepromARMtool.

After check document and source code we find eepromARMtool only support flash I211 iNVM.

But we want to flash I211 NVM on ARM platform.

Does any tool can flash I211 NVM on ARM platform?

Best regards,

Vic

0 Kudos
CarlosAM_INTEL
Moderator
4,644 Views

Hello, vic918 :

Thanks for your update.

In order to help you, we have sent you an email.

We hope that this information may help you.

Best regards,

Carlos_A .

0 Kudos
vlin10
Beginner
4,644 Views

Hi Carlos,

I do not receive the email that you mention which include some information can help me.

Could you send it to me again?

Best regards,

Vic

0 Kudos
CarlosAM_INTEL
Moderator
4,648 Views

Hello, vic918 :

Thanks for your reply.

We have sent the email again.

We hope that it can help you.

Best regards,

Carlos_A.

0 Kudos
vlin10
Beginner
4,648 Views

Hi Carlos,

Thanks for your help. I already receive eepromARMtool again.

The eepromARMtool only support flash I211 internal NVM.

This is explained in the document # 523420 charter 2.1 Supported Devices.

But we want to a tool which can flash I211 NVM on ARM platform.

Does you know any tool can flash I211 NVM on ARM platform?

Best regards,

Vic

0 Kudos
CarlosAM_INTEL
Moderator
4,648 Views

Hello, vic918:

Thanks for your reply.

The information that may help you is stated in the answers to the questions 2.9, 2.14, 2.15, and 2.16; on pages 6 and 8 of the https://www.intel.com/content/dam/www/public/us/en/documents/faqs/ethernet-controller-i210-i211-faq.pdf Intel(R) Ethernet Controller I210/I211 Frequently Asked Questions [FAQs] document 335346.

We hope that this information may help you.

Best regards,

Carlos_A.

0 Kudos
cqing
Beginner
4,648 Views

Dear Carlos A:

I also need the tool for arm 32. please send emil to me about the source link !

Thank you very much!

Best Regards

Qing

0 Kudos
CarlosAM_INTEL
Moderator
4,648 Views

Hello, CH_Qing:

Thank you for contacting Intel Embedded Community.

The https://cdrd.intel.com/v1/dl/getcontent/572162 Intel I210, I211, and X550 EEPROM Access Tool (EAT) document # 572162 has the requested information.

This tool is accessible when you are logged into your Resource & Design Center (RDC) privileged account as well.

It can be requested by filling out the https://www.intel.com/content/www/us/en/forms/design/contact-support.html RDC Account Support form.

We hope that this information may help you.

Best regards,

Carlos_A.

0 Kudos
RWu
New Contributor I
4,648 Views

Hi Carlos,

Could you please provide us eeupdate ARM tool and the Usage guide.

Please send to mailto:jackpeng@aaeon.com.tw jackpeng@aaeon.com.tw

Thanks in advance

Best Regards

0 Kudos
CarlosAM_INTEL
Moderator
4,648 Views

Hello, Aaeon:

Thank you for contacting Intel Embedded Community.

Could you please confirm if this request is the same state in the Carlos_A.

0 Kudos
DAnde8
Beginner
4,648 Views

was there a resolution to this? i am looking for the eeupdate o r eeprom for AARCH64 (64-bit ARM) as well....

0 Kudos
CarlosAM_INTEL
Moderator
4,648 Views

Hello, DavidAnders:

Thank you for contacting Intel Embedded Design Center.

In order to be on the same page, could you please tell us the part number of the Intel device related to your consultation?

By the way, could you please let us know if this question is related to a technical problem?

Waiting for the information that should answer these questions.

Best regards,

Carlos_A.

0 Kudos
cqing
Beginner
4,648 Views

Dear Carlos_A.

I used the I210 on my imx6q board.

$ ./EepromAccessTool

Copyright(C) 2017-2018 by Intel(R) Corporation

NIC BUS DEV FUN Silicon Memory Type Present

=== === === === ===== ======================

1 1 0 0 I210 INVM+FLASH

$ ./EepromAccessTool -NIC=1 -f=Dev_Start_I210_Copper_NOMNG_8Mb_A2_3.25_0.03.hex

Intel(R) EEPROM Access Tool NVM/OTP Programming Example Tool Version 0.7.6

Provided under the terms of a CNDA. Do Not Distribute.

Copyright(C) 2017-2018 by Intel(R) Corporation

size is 100000

Hardware rejected opcode=1000000, addr=0

WriteFlswFlashCommand in WriteNvmFlswI210 failed

Hardware rejected opcode=1000000, addr=2

WriteFlswFlashCommand in WriteNvmFlswI210 failed

Hardware rejected opcode=1000000, addr=4

WriteFlswFlashCommand in WriteNvmFlswI210 failed

Hardware rejected opcode=1000000, addr=6

WriteFlswFlashCommand in WriteNvmFlswI210 failed

$ cat /proc/bus/pci/devices

0000 16c3abcd 13e 1c00000 0 0 0 0 0 1d00000 100000 0 0 0 0 0 10000 pcieport

0100 80861531 13e 1000000 0 1001 1800000 0 0 0 800000 0 20 4000 0 0 0

and the P12 was pull down.

And this is what root cause ? thank you very much!

Best Regards

Qing

0 Kudos
CarlosAM_INTEL
Moderator
4,648 Views

Hello, CH_Qing:

Thanks for your replies.

In order to be on the same page, could you please let us know the sources that you have used to develop your design? By the way, could you please let us know if it has been reviewed by Intel?

Waiting for your answer to these questions.

Best regards,

Carlos_A.

0 Kudos
cqing
Beginner
4,648 Views

Dear Carlos_A.

I just want to see if the selected image is correct?

my case is :

1. use the I210 internal phy, so use the coper

2. just use the i210 as a normal ethernet, and no other special needs

3. flash is 8Mb

so I selected the image Dev_Start_I210_Copper_NOMNG_8Mb_A2_3.25_0.03.hex in Flash Images/I210/Twisted_pair.

and I used the tool is eepromaccesstool-0-7-6. so the image files is hex format.

Is correct for my case ? thank you very much!

And another question is , If I want to modify the mac address and led blank logic, What I should do ?

Thanks very much!

Best Regards

Qing

0 Kudos
cqing
Beginner
4,648 Views

Dear Carlos_A.

Thanks very much ! How can I do for that intel review my design?

Best Regards

Qing

0 Kudos
CarlosAM_INTEL
Moderator
3,981 Views

Hello, CH_Qing :

Thanks for your reply.

The procedure is stated in the https://edc.intel.com/Tools/Design-Review/Default.aspx?language=en&r=380356071 Design Review Services website.

We hope that this information may help you.

Best regards,

Carlos_A.

0 Kudos
Reply