- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I would like to declare the arrays X, Y, DX, DY, and A in the shared data of theMODULE below, and eliminate the associated dummy arguements from Subroutine SplineSetup(). These arrays areused by Sub, Spline() in the same MODULE, but are not used outside the MODULE. However,the DIMENSION of the arraysis a variable 'N' which is a dummy arg for Sub. SplineSetup(), and this seems to prevent including the arrays in the MODULE's shared data. Is there a way to do this?
Thanks for any comments.
[plain]MODULE SplineFit ! shared data here CONTAINS SUBROUTINE SplineSetup(N,X,Y,DX,DY,A) ! ! code below is modified version of NA 300 piece wise cubic spline interpolation ! example code ! ! N -- number of data points ! X -- X(1:N) array or X input values to be used for interpolation ! Y -- Y(1:N) array or Y input values to be used for interpolation ! DX, DY, A coefficient arrays returned IMPLICIT NONE INTEGER N, N1 INTEGER ib INTEGER i REAL, DIMENSION(N) :: X, Y REAL, DIMENSION(N) :: DX, DY, A REAL, DIMENSION(N) :: T REAL PIV A(1) = 0.0 A(N) = 0.0 N1 = N - 1 do i = 1, N1 DX(i) = X(i+1) - X(i) DY(i) = (Y(i+1) - Y(i))/DX(i) end do T(1) = 0.0 do i = 2, N1 PIV = 2.0*(DX(i-1)*DX(i)) - DX(i-1)*T(i-1) T(i) = DX(i)/PIV A(i) = (DY(i) - DY(i-1) - DX(i-1)*A(i-1))/PIV end do do ib = 2, N1 i = N + 1 - ib A(i) = A(i) - T(i)*A(i+1) end do ! iError = 1 RETURN END SUBROUTINE SUBROUTINE Spline(N,XX,S) ! ! INPUT -- XX any value ! OUTPUT -- S = Spline evaluated at XX INTEGER K INTEGER N REAL XX, S REAL W, V REAL, DIMENSION(N) :: X, Y REAL, DIMENSION(N) :: DX, DY, A K = 1 ! lower bound do if(XX .LT. X(K)) then K = K-1 if(K .EQ. 0) CYCLE K = 1 S = Y(1) + (DY(1) - DX(1)*A(2))*(XX-X(1)) RETURN end if ! if(XX .GE. X(K)) then EXIT do loop EXIT end do ! upper bound do if(XX .GE. X(K+1)) then K = K+1 if(K .NE. N) CYCLE K = N - 1 S = Y(N) + (DY(K) + DX(K)*A(K))*(XX-X(N)) RETURN end if ! if(XX .LT. X(K+1)) then EXIT do loop EXIT end do W = (XX - X(K))/DX(K) V = 1.00 - W S = W*Y(K+1) + V*Y(K) + (DX(K)**2)*((W**3 - W)*A(K+1) + (V**3 - V)*A(K)) RETURN END SUBROUTINE END MODULE[/plain]
Link Copied
3 Replies
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Put the arrays before the contains and make them allocatable.
Module SplineFit
real, allocatable :: X(:)
real, allocatable :: Y(:)
real, allocatable :: DX(:)
real, allocatable :: DY(:)
real, allocatable :: A(:)
CONTAINS
Subroutine SplineSetup(N)
real T(N) ! Automatic local array
! remove the declarations for X,Y,DX,DY,A
! They will be available from host association
! Allocate the arrays.
! If you are calling this routine many times with different values of N you will need to
! deallocate any existing allocations.
! It is also a good idea to check for allocate errors as a precaution.
integer :: ierr
allocate(X(N),stat=ierr)
repeat for Y, DX, DY and A
remove the declarations of real X, Y DX, DY and A from Subroutine Spline, they will be available via host association once they have been allocated by SplineSetup
Les
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Les, yourexplanation was easy to follow, thank you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
if you want to keep the arrays only useable inside the module add ',private' in the declaration.
real, allocatable,private :: X(:)
Frank
real, allocatable,private :: X(:)
Frank
![](/skins/images/C4F7392A5C68ACA60290C9576F107044/responsive_peak/images/icon_anonymous_message.png)
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page