- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have tried all the settings, and even made the custom win 10 iso . The setup i follow, The bios are set right according to everything i have read. So i boot to my usb and install windows, then when it reboots the computer Nothing. It just goes back into the bios. If i turn off the Optane in the bios, and boot to ahci then the windows boot partition works and i can continue installing windows. Then when i get to the desktop, and install the software it reboots, changes my setting in the bios back to Intel Rst Premium with intel optane acceleration, and im stuck at where i was before, nothing, boot loop back into bios cause it wont boot the windows partition. If i turn off again it then boots into safe mode and i see the intel optane pop up on the screen so fast and then i dont get to do anything, computer restarts. So i dont know what it is. I have tried everything and older windows versions. my hardware is fine and i just have the 2 drives installed. windows and the bios see the hardware. so it is a bios issue or intel optane drivers/installer.
Link Copied
- « Previous
-
- 1
- 2
- Next »
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi TekSoup ,
Thanks for the feedback and the video provided. We will pass this information over to our additional resources.
Regards,
Junior M.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
here is Gigabyte info/email from there customer support. They say dont turn on rst. well when i enable intel optane that is rst. I have tried 30 different ways and built custom iso and used plain iso and different builds of windows. I have over 30 years of advanced computer experience, Been useing thunderbolt on PC since the begining. I went and bought and built a whole new system just to see if there was something wrong. well the asrock system works and no problems with the install. If i am to test the Gigabyte system any further i will have to buy Another Optane drive, im not gonna pull it from the Working Asrock System.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi TekSoup ,
Thanks for the information provided.
Could you please let us know the exact steps you followed in order to enable the Optane(TM) in the Asrock* motherboard?
We will be waiting for your response in order to further investigate this situation.
Regards,
Junior M.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi TekSoup ,
We would like to know if you read our previous post. If you have any other questions, we'll be waiting for your response.
Regards,
Junior M.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes i will, i have been busy. i will try to get to it in the next few days.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi TekSoup ,
Thanks for the update.
We will be waiting for the information.
Regards,
Junior M.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi TekSoup ,
We haven't heard back from you in a while. Have you been able to get the steps you followed in order to enable the Optane(R) on the new motherboard?
Regards,
Junior M.
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- « Previous
-
- 1
- 2
- Next »