- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
The dgelsd issue (http://software.intel.com/en-us/forums/showthread.php?t=61809) doesn't seem to be fully addressed.
I'm getting "MKL ERROR: Parameter 4 was incorrect on entry to DLASCL" when running dgelsd on AMD processor
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 5
model name : AMD Opteron Processor 250
stepping : 10
cpu MHz : 1000.000
cache size : 1024 KB
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow up
bogomips : 1996.13
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp
Could you please check this?
Thanks.
Jaewon
I'm getting "MKL ERROR: Parameter 4 was incorrect on entry to DLASCL" when running dgelsd on AMD processor
$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 5
model name : AMD Opteron Processor 250
stepping : 10
cpu MHz : 1000.000
cache size : 1024 KB
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext lm 3dnowext 3dnow up
bogomips : 1996.13
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp
Could you please check this?
Thanks.
Jaewon
Link Copied
5 Replies
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jaewon,
what MKL version are you using?
--Gennady
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Gennady,
It was 10.2.5. Would it make a difference with 10.3?
Jaewon
It was 10.2.5. Would it make a difference with 10.3?
Jaewon
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
This is unexpected result behavior. we will check it on our side and will back asap.
--Gennady
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Jaewon,
I've reproduced the issue.It will be fixed in the next MKL 10.2 Update. This concerns MKL 10.3.b too, and will be fixed in MKL 10.3.0 as well.
Michael.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Jaewon,
Could you please check if the probelm is still exists with latest MKL 10.2 Update 6 version released yesterday.
--Gennady
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page