- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello,
we are using Intel VTune 2015 for profiling our application which is running under CentOS 5.11.
Our application uses c++ signals for the control flow. When trying to do a basic hotspots analysis using amplxe-cl command line tool with the following parameters:
-duration 20 --run-pass-thru=--profiling-signal=1
VTune yields the following error message when detaching after the 20 seconds duration. Alternative to the number 1 I also tried number 4 without any change in results.
amplxe: Error: Assertion failed: handler_ex1445: obj->is_first_class_handler_set[signo] == 1 : BUG! : signo == 1. Please contact the technical support.
Without using "--run-pass-thru=--profiling-signal=1" as parameter the signal handlers of our application do not work after profiling and the process is ended when receiving a signal.
Please provide guidance on how to use VTune in this scenario.
Best Regards,
Stephan
Link Copied
- « Previous
-
- 1
- 2
- Next »
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@ Wolfgang K,
We cannot guarantee any exact time for next release to users . Your expectation is about 5-8 weeks from U2 based on my experience...again, it is not the official time, just my estimation. A formal time frame for next release is business confidential...thanks for your understandings.
Regards, Peter
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Now VTune(TM) Amplifier XE 2015 Update 3 is ready, this version has solved the issue of Ctrl-C handling for TPSS collector.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Peter,
we tested VTune(TM) Amplifier XE 2015 Update 4 with the SignalsTest application and confirm that the handling of ctrl-c is fixed.
The real application which we need to profile does not only use Signals for control flow but also for its timing. This was not covered by the SignalsTest application.
When we profile our real application using VTune(TM) Amplifier XE 2015 Update 4 it is still crashing after profiling is finished, most likely because of the broken signal handler which controls the timing in our application. Therefore I extended the SignalsTest application and added the same signal handler which is used for timing to it. The error can be reproduced using this extended application with all of the following commands
./amplxe-cl -collect hotspots -duration 20 -target-process SignalsTest
./amplxe-cl -collect hotspots -duration 20 [-run-pass-thru=-no-altstack] -target-process SignalsTest
> Kills process after collection
./amplxe-cl -collect hotspots -duration 20 --run-pass-thru=--profiling-signal=33 -target-process
./amplxe-runss --data-limit-mb=500 --stack-stitching --follow-child --itt-config=frame --stackwalk=offline -profiling-signal 33 -duration 5 --type=cpu:counters:nostack --type=cpu:stack --target-process SignalsTest
> Kills process immediately
The error message of the application is always 'Real-time signal 4'.
Could you please forward the new application to a developer so that he can have a look into the issue.
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
OK, I have escalated your file to developer for re-investigating on timing control.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Peter,
do you have an update concerning the re-investigation? Can the issue be reproduced at your side using the new SignalsTest application?
Thanks and Best Regards,
Stephan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
@ Stephan,
I will verify this with developer and get back to you soon. Sorry for late.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes. I launched SignalsTest, then ran VTune in another console,
# amplxe-cl -collect hotspots -duration 20 --run-pass-thru=--profiling-signal=33 -target-process SignalsTest
It stopped immediately, Elapsed time on VTune's output was "0", that was unexpected since we set duration as "20". This is a bug in 2015 U4.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Using latest VTune(TM) Amplifier XE 2017 beta update 1 has fixes this issue.
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- « Previous
-
- 1
- 2
- Next »