eepromARMtool

[MPatt3]

Where do I find the eepromARMtool code? I am working on an ARM based design that uses an i210. I would like to program the NVM via this tool so that I can get the driver to load.

Regards,

Matt

[MPatt3]

Do you mean program it with a 3rd party programmer off board? With a blank part the eeprom arm tool crashes before we can program anything.

[ldong6]

Hi AdolfoS, I am working on an ARM based design that uses an i210. Where do I find the eepromARMtool code? thanks.

email: mailto:[email protected] [email protected]

[SConn1]

Hi Aldolfo,

We are also looking to program the I210 on an ARM platform. We are looking to program the INVM. Do you have a tool for that?

Thanks

[Natalie_Z_Intel]

Hi, Seamus! We'll get back with you on this question. We see that you have /message/12657?et=watches.email.thread# 12657 another post which we'll address in this thread, too. LynnZ.

[idata]

Hello Seamus,

I've sent you an e-mail with the requested tool. Please confirm that you have received it.

If you have any other question please let us know.

Best regards,

Jimmy.

[PPast3 · Accepted solution]

Hi Adolfo,

I'm look for the same tool (eepromARMtool) i need to program my new hardware with i210 into SerDes Mode could you email the tool also.

Thanks,

Pawel

[Sofian]

Hi @CarlosAM_INTEL 

I'm looking for the same tool for ARM CPU based (eepromARMtool) and I need to test the tools on i211, could you send me email for the tool also ?

Thanks,

Sofian

[CarlosAM_INTEL]

Hello, @Sofian:

Thank you for contacting Intel Embedded Community.

The Intel I210, I211, and X550 EEPROM Access Tool (EAT) document # 572162 is the updated version of the requested tool. It can be found when you are logged into your Resource & Design Center (RDC) privileged account at the following website:

http://www.intel.com/cd/edesign/library/asmo-na/eng/572162.htm

The RDC Account Support form is the channel to process your account update request or any inconvenience related to the provided website. It can be found at:

https://www.intel.com/content/www/us/en/forms/design/contact-support.html

Best regards,

@CarlosAM_INTEL.

[Sofian]

Hi @CarlosAM_INTEL 

Thanks for your reply.

I got problem when I try to access the link that you gave me.

http://www.intel.com/cd/edesign/library/asmo-na/eng/572162.htm

so I open the case #04828040.

Thanks,
Sofian

[CarlosAM_INTEL]

Hello, @Sofian:

Thanks for your answer.

Actually, we suggest following our last suggestion to solve the mentioned inconvenience.

Best regards,

@CarlosAM_INTEL.

[ccbow]

Hello, We are working with the I210 with an external eeprom and would like to get a copy of the eepromARMtool to get started with getting the chip up and running.

Can you please send me a copy.

[Diego_INTEL]

Hello @ccbow,

Thank you for contacting Intel Embedded Community.

You can check document #572162 - EEPROM Access Tool [EAT] in RDC.

You will need a Premier account in order to get access to the document, you may check this article:

https://www.intel.com/content/www/us/en/support/articles/000058073/programs/resource-and-documentation-center.html

Best regards,

@Diego_INTEL 

[WSchr1]

Hi Adolfo,

I'm aols looking to get the eepromARMtool, could you send me a copy?

Thanks in advance,

Wolfgang

[Gabriel_T_Intel]

Hello Wolfgang,

Welcome to the Intel Embedded Community.

We are going to contact you by email.

Regards,

Gabriel Thomas

[STuba]

Hello Adolfo,

We are also looking to program the EEPROM of the I210 and 82574L chips on an i.MX6 ARM platform.

Can you please send me the source code of your tool?

Thank you and Best Regards

Stefano

[ACest]

Hi,

we need to program I210 flash from a ARM procesor, could you send to me the eepromARMtool and HEX to put in flash?

Best Regards,

Alberto

[CarlosAM_INTEL]

Hello Alberto,

Thank you for contacting the Intel Embedded Community.

We will contact you via email to help you.

Best Regards,

Carlos_A.

[PHall1]

Hello, We are working with the I210 with an external eeprom and would like to get a copy of the eepromARMtool to get started with getting the chip up and running. Can you please send me a copy.

[CarlosAM_INTEL]

Hello Peter_Hall,

Thank you for contacting the Intel Embedded Community.

We will contact you via email to help you.

Best Regards,

Carlos_A.

[AFade]

Hello AdolfoS

Could you also send ARM tool to me?

[CarlosAM_INTEL]

Hello AlexandrFadeev,

Thank you for contacting the Intel Embedded Community.

We will contact you via email to help you.

Best Regards,

Carlos_A.