- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi,
We have developed an ethernet driver for Cyclone V SoC in bare-metal programming. When we are transmitting more than 80 bytes per packet in our customized board it is getting failed. But the board can receive up to 1200 bytes in a packet.
We have used the UDP protocol.
I have tried pinging the IP with 100bytes ethernet getting unresponsive.
we have taken the Arria10 driver as a reference and LWIP 2.0.3 as IP stack.
We have KSZ9021RN PHY IC and configured as 10/100 Ethernet speed.
Checked the tx and RX descriptor's size and packet length and found them adequate for 1024 bytes. I have attached the code.
Seeking help from the experts.
Kindly do the needful.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Aik Eu,
The above issue is soved. Some macros related to dma configuration are commanded in code. After removing the command it is solved.
Thanks.
コピーされたリンク
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Ranjithkumar828,
I will try to consult and see if there is any information which might help to answer your question.
Thanks.
Regards,
Aik Eu
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Aik Eu,
The above issue is soved. Some macros related to dma configuration are commanded in code. After removing the command it is solved.
Thanks.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Ranjithkumar828..
Could you share the driver you created to send/receive UDP packets from the ethernet port?
I'm trying to do the same thing you did but with a DE10 nano board, for now without success, because I can't find a baremetal driver on the internet that allows me to use the ethernet port to send simple raw packets.
Would you be willing to give me some help?
Thank you,
Luca.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Aikeu,
As i sent mail, When we trying to boot from QSPI few interface like Etherenet and OLED (SPI) is not working. Please check that and provide solution for the same.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Ranjithkumar828,
I think you will require to create another case related to the QSPI booting Ethernet and OLED function was not working for tracking purpose.
Thanks.
Regards,
Aik Eu
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Ranjithkumar828,
Try to enable one ethernet or OLED function at a time for your system to boot up. This might help to see if those are related to timing issue due to initialization when perform QSPI boot up.
Thanks.
Regards,
Aik Eu
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Hi Ranjithkumar828,
I am closing this thread for now. Do consider open a new thread for the to other issues that you have mentioned.
Thanks.
Regards,
Aik Eu