License: Compilation Error

[Altera_Forum]

Hello Together! 

 When I compile my project I get following error message: Current license file does not support incremental compilation (and I will not use it :-)).  That happens since I'm clicked "Add Node to SignalTap II Logic Analyzer". My next compilation shows mentioned message. Removing generated files from project didn't solve the problem. I also checked .qsf-file for entry INCREMENTAL_COMPILATION FULL_INCREMENTAL_COMPILATION as mentioned in Quartus II Help document but there is no word INCREMENTAL at all. In window "Settings" "Incremental Compilation" I couldn't select anything.   Used Version:  Quartus II 9.0 Buid 235 Web Edition Service Pack Installed: 2 Help Version: Quartus II Help Version 9.0   Thanks for your support!   Best regards R. Schrauth

[Altera_Forum]

--- Quote Start ---  Hello Together!   When I compile my project I get following error message: Current license file does not support incremental compilation (and I will not use it :-)).  That happens since I'm clicked "Add Node to SignalTap II Logic Analyzer". My next compilation shows mentioned message. Removing generated files from project didn't solve the problem. I also checked .qsf-file for entry INCREMENTAL_COMPILATION FULL_INCREMENTAL_COMPILATION as mentioned in Quartus II Help document but there is no word INCREMENTAL at all. In window "Settings" "Incremental Compilation" I couldn't select anything.   Used Version:  Quartus II 9.0 Buid 235 Web Edition Service Pack Installed: 2 Help Version: Quartus II Help Version 9.0   Thanks for your support!   Best regards R. Schrauth  --- Quote End ---    Hi,  are you using Signaltap ?  Kind regards  GPK

[Altera_Forum]

Hi GPK, 

I don't use Signal Tap II Analyser ("Settings", "SignalTap II Logic Analyser", "Enable Signal Tap Logic Analyser" is OFF). To give a complete overview I add all error messages which occure:    Error: Current license file does not support incremental compilation Error: Quartus II Analysis & Synthesis was unsuccessful. 1 error, 0 warnings *Error: Peak virtual memory: 190 megabytes *Error: Processing ended: Thu May 20 09:45:25 2010 *Error: Elapsed time: 00:00:07 *Error: Total CPU time (on all processors): 00:00:04 Error: Quartus II Full Compilation was unsuccessful. 3 errors, 0 warnings   I'm not familiar with HDL-programming language and use only schematics. Are there any entries in files which force to use incremental compilation?   Kind regard R. Schrauth

[Altera_Forum]

--- Quote Start ---  Hi GPK, I don't use Signal Tap II Analyser ("Settings", "SignalTap II Logic Analyser", "Enable Signal Tap Logic Analyser" is OFF). To give a complete overview I add all error messages which occure:    Error: Current license file does not support incremental compilation Error: Quartus II Analysis & Synthesis was unsuccessful. 1 error, 0 warnings *Error: Peak virtual memory: 190 megabytes *Error: Processing ended: Thu May 20 09:45:25 2010 *Error: Elapsed time: 00:00:07 *Error: Total CPU time (on all processors): 00:00:04 Error: Quartus II Full Compilation was unsuccessful. 3 errors, 0 warnings   I'm not familiar with HDL-programming language and use only schematics. Are there any entries in files which force to use incremental compilation?   Kind regard R. Schrauth  --- Quote End ---    Hi,  maybe I found your problem. I assume you tried to use signaltap, right ?  Look into your <>.qsf . Do you find a line like this :  set_global_assignment -name PARTITION_NETLIST_TYPE POST_FIT -section_id Top  If yes, remove this line and all should work.  When you try to use signaltap and your node selection is set to "Signaltap post-fitting" you will be ask to set the Top partition to "Post-fit". Unfortunately this means incremental compilation, which is not supported by the Web Edition. I would say that is a bug or at least a weakness of this Quartus Version.   Kind regards  GPK

[Altera_Forum]

Hi GPK, 

sorry, but entry you mentioned isn't there. I only found this: "set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top". I attached my .qsf file as pdf. Perhaps you could find the wrong entry easily.   Kind regards R. Schrauth

[Altera_Forum]

--- Quote Start ---  Hi GPK, sorry, but entry you mentioned isn't there. I only found this: "set_global_assignment -name PARTITION_NETLIST_TYPE SOURCE -section_id Top". I attached my .qsf file as pdf. Perhaps you could find the wrong entry easily.   Kind regards R. Schrauth  --- Quote End ---    Hi,  now I can only guess. Add following line in the qsf :  set_global_assignment -name INCREMENTAL_COMPILATION OFF  Kind regards  GPK

[Altera_Forum]

Hello, 

thanks for your support but I couldn't solve the problem. Finally I designed a new project and entered the whole stuff again. It took few hours but now compilation works :-).   Kind regards R. Schrauth