- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have just started having problems using my usual route to the Fortran forum message board. The forum page I now get when I enter
http://www7.compaq.com/forum?
sends me to
http://www7.compaq.com/forum?CPQ@@!top=1
and this page contains only management software under application development, with 'compilers' omitted, so I cannot get to the Fortran forum by clicking on 'compilers'.
http://www7.compaq.com/forum?
sends me to
http://www7.compaq.com/forum?CPQ@@!top=1
and this page contains only management software under application development, with 'compilers' omitted, so I cannot get to the Fortran forum by clicking on 'compilers'.
I went back to an early e-mail that I recieved after logging in December 2000 and used a link that it contained in order to get here and post this message. What's going on?
Link Copied
11 Replies
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Apparently some clever guy decided this is a good method to access the board. Worse still, ''Refresh' leads (probably 15+ minutes after initial login) to request for relogin, and then nowhere, so I have to go through torturing procedure of accessing forum home, re-logging in, and through two links (Forum->Compilers->Fortran) to the Fortran Forum. Could you please retreat this to the previous state? Why should anyone be requested to log in if he only wants to see what's new?
Jugoslav
Jugoslav
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
This was a surprise to me too. I've filed a complaint about it.
Steve
Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Should be back to normal now...
Steve
Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Kind of a strange new forum kink. Before I post this message, when I view the forum, the only topic is 'Printing list of project files...' and all the other topics are sub-topics of this one! Who knows what will happen after posting this message!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Well, now we know what happens! :-)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Damn - I wish Houston would stop messing around with things! I'll get this fixed...
Steve
Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I hope there wasn't something in my reply to 'Printing list of project files...' that messed it up. The problem seemed to occur right after I was notified my message was posted.
Dick
Dick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
As a matter of fact, there was - an unclosed table tag. Unfortunately, the forum "rendering" software gets very confused by malformed HTML in messages or even in source. I've asked to get this resolved, but am not sure how successful I'll be.
Sometimes I take to editing posts to replace problematic characters with <, > and "
Steve
Sometimes I take to editing posts to replace problematic characters with <, > and "
Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I hope there wasn't something in my reply to 'Printing list of project files...' that messed it up. The problem seemed to occur right after I was notified my message was posted.
Dick
Dick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Sorry about the double-post. After taking a telephone call, I didn't remember that I had already pressed 'Okay'. Shouldn't there be some feedback to that--or did I overlook it. Also, it would be nice if the Edit button would actually allow changes--or, once again, is there something I'm overlooking.
Dick
Dick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I reported the problem with the Edit button again...
Steve
Steve
Reply
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page