- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
コピーされたリンク
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
With a properly installed Intel Parallel Studio XE 2013 SP1, you should see an entry in the Windows Start Menu for "All Programs : Intel Parallel Studio XE 2013". One of the sub entries under that item will be something along the lines of "Command Prompt with Intel Compiler XE v13..." Depending on what components you installed, you should see one or two command window shortcuts. Choose the one that matches the Abaqus that you have (32- or 64-bit).
As to " I cannot see the command prompt", you did not tell us where you expect to see it and what you did to locate it.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
I've been looking recently at complaints from Abaqus users about use of newer Intel Fortran versions, and the problems they have are all caused by Abaqus instructions and setup scripts that are inappropriately specific to one Fortran and VS version. The recommended way is to use the "Command Prompt" shortcut we install in the Start menu under Intel Parallel Studio XE 2013 SP1 - and once that is open, and you "cd" to a writable folder, you invoke Abaqus scripts from there. The paths to the compiler and libraries will already be set up.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
The normal start menu advice is good for Windows 7. If OP were using a newer Windows, different advice might be needed.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Tim Prince wrote:
The normal start menu advice is good for Windows 7. If OP were using a newer Windows, different advice might be needed.
Yes. I forgot to mention that, since I do not use a touch-screen (my screen is located comfortably far enough to read, but is beyond reach), one of the first things that I do after any W8.1 installation is to install Classic-Start-Menu because W8.1 is (for me) unusable without the start-menu.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
If you type "command" into the search bar, you'll see under folders "Command Prompt with Intel Compiler XE 15.0". Open that, and there are the shortcuts for the command environment. I usually copy these to my desktop and change the "Start in" property as desired.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Thanks everyone for the suggestions! Where can I get a list of all versions of Fortran Compilers? That way I can download and install properly the suitable version for Abaqus!
Thanks,
Aditya
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
See here for instructions on getting older versions. I strongly recommend not starting out with an old version as you may encounter issues. Abaqus should work fine with the latest version, if the setup is done properly.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Thanks Steve! I know the procedure to get older versions. What I want is a list of all versions. I was able to find that through a link in the 5th point of the above procedure, however now the link does not work?
Thanks,
Aditya
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
https://software.intel.com/en-us/articles/intel-fortran-compiler-for-windows-required-and-optional-microsoft-development-software has a list of all of the versions of Intel Visual Fortran. The first part discusses the current version and a list at the end names all the prior versions back to 8.0 (before that, Intel Fortran was a very different product.)
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Thanks Steve! Actually the list that I was talking about was found through a link seen in 5th point of this link- https://software.intel.com/en-us/articles/older-version-product
I was able to open the the link in 5th point (https://software.intel.com/en-us/articles/intel-compiler-and-composer-update-version-numbers-to-compiler-version-number-mapping) and get the list few days back, however, know I am not able to do so now. It says page not found.
Thanks,
Aditya
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Thanks for letting us know - I'll find out what happened to that article and get it restored if I can.
- 新着としてマーク
- ブックマーク
- 購読
- ミュート
- RSS フィードを購読する
- ハイライト
- 印刷
- 不適切なコンテンツを報告
Thanks Steve! Will wait for your reply
Regards,
Aditya Nikam
