Intel® Quartus® Prime Software
Intel® Quartus® Prime Design Software, Design Entry, Synthesis, Simulation, Verification, Timing Analysis, System Design (Platform Designer, formerly Qsys)
16886 Discussions

error in .VWF if using IP

MFort6
Beginner
‎07-29-2020 10:19 AM
1,509 Views

Hi below is my code, it simulated perfectly but when i want to check the outputs using the .VWF file i am getting the following errors which are listed at the bottom.  i am using Altera Stratix® V GX FPGA (5SGXEA7N2F45C2)Screenshot (228).pngScreenshot (229).pngScreenshot (230).pngScreenshot (227).png and quartus 16.1 version

code:

module data_transfer(
input clk,
output [0:0] tx_serial_data

);
reg [79:0] tx_pma_parallel_data = 80'h2451BE17A3;
reg reset = 0;
wire [139:0] reconfig_to_xcvr;
wire [91:0] reconfig_from_xcvr;
wire reconfig_busy;
wire [31:0] reconfig_mgmt_readdata;
wire reconfig_mgmt_waitrequest;
wire clkout;
wire pll_powerdown;
wire tx_analogreset;
wire tx_digitalreset;
wire tx_ready;
wire tx_cal_busy;

/*trans_rec tx_transrec (
.pll_powerdown(pll_powerdown), // low
.tx_analogreset(tx_analogreset), // off and add Transceiver PHY Reset Controller
.tx_digitalreset(tx_digitalreset), // off and add Transceiver PHY Reset Controller
.tx_pll_refclk(clk), // refclk
.tx_pma_clkout(clkout), // clkout
.tx_serial_data(tx_serial_data), // data
.tx_pma_parallel_data(tx_pma_parallel_data), // tx_pma_parallel_data.tx_pma_parallel_data
.pll_locked(), // low
.tx_cal_busy(tx_cal_busy), // out_busy
.reconfig_to_xcvr(reconfig_to_xcvr), // reconfig_to_xcvr.reconfig_to_xcvr
.reconfig_from_xcvr(reconfig_from_xcvr) // reconfig_from_xcvr.reconfig_from_xcvr
);*/

trans_reconfig recofig (
.reconfig_busy(), // reconfig_busy.reconfig_busy
. mgmt_clk_clk(clk), // mgmt_clk_clk.clk
.mgmt_rst_reset(), // low
.reconfig_mgmt_address(), // reconfig_mgmt.address
.reconfig_mgmt_read(), // .read
.reconfig_mgmt_readdata(), // .readdata
.reconfig_mgmt_waitrequest(), // .waitrequest
.reconfig_mgmt_write(), // .write
.reconfig_mgmt_writedata(reconfig_mgmt_writedata), // .writedata
.reconfig_to_xcvr(reconfig_to_xcvr), // reconfig_to_xcvr.reconfig_to_xcvr
.reconfig_from_xcvr(reconfig_from_xcvr) // reconfig_from_xcvr.reconfig_from_xcvr
);
reset_cont reset_controller (
.clock(clk), // clock.clk
.reset(reset), // reset.reset
.pll_powerdown(pll_powerdown), // pll_powerdown.pll_powerdown
.tx_analogreset(tx_analogreset), // tx_analogreset.tx_analogreset
.tx_digitalreset(tx_digitalreset), // tx_digitalreset.tx_digitalreset
.tx_ready(tx_ready), // tx_ready.tx_ready
.pll_locked(), // pll_locked.pll_locked
.pll_select(), // pll_select.pll_select
.tx_cal_busy(tx_cal_busy), // tx_cal_busy.tx_cal_busy
.rx_analogreset(), // rx_analogreset.rx_analogreset
.rx_digitalreset(), // rx_digitalreset.rx_digitalreset
.rx_ready(), // rx_ready.rx_ready
.rx_is_lockedtodata(), // rx_is_lockedtodata.rx_is_lockedtodata
.rx_cal_busy() // rx_cal_busy.rx_cal_busy
);

endmodule

 

 

error:

Completed successfully.

**** Running the ModelSim simulation ****

C:/intelFPGA/16.1/modelsim_ase/win32aloem/vsim -c -do data_transfer.do

Reading C:/intelFPGA/16.1/modelsim_ase/tcl/vsim/pref.tcl

 

# 10.5b

 

 

# do data_transfer.do

# ** Warning: (vlib-34) Library already exists at "work".

# Model Technology ModelSim - Intel FPGA Edition vlog 10.5b Compiler 2016.10 Oct 5 2016

# Start time: 12:02:55 on Jul 29,2020

# vlog -work work data_transfer.vo

# -- Compiling module data_transfer

 

#

# Top level modules:

# data_transfer

# End time: 12:02:55 on Jul 29,2020, Elapsed time: 0:00:00

# Errors: 0, Warnings: 0

 

# Model Technology ModelSim - Intel FPGA Edition vlog 10.5b Compiler 2016.10 Oct 5 2016

# Start time: 12:02:55 on Jul 29,2020

# vlog -work work Waveform.vwf.vt

# -- Compiling module data_transfer_vlg_vec_tst

#

# Top level modules:

# data_transfer_vlg_vec_tst

# End time: 12:02:55 on Jul 29,2020, Elapsed time: 0:00:00

# Errors: 0, Warnings: 0

 

# vsim -novopt -c -t 1ps -L stratixv_ver -L altera_ver -L altera_mf_ver -L 220model_ver -L sgate_ver -L altera_lnsim_ver work.data_transfer_vlg_vec_tst

# Start time: 12:02:55 on Jul 29,2020

# Loading work.data_transfer_vlg_vec_tst

# Loading work.data_transfer

# ** Error: (vsim-3033) data_transfer.vo(1897): Instantiation of 'stratixv_hssi_refclk_divider' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# Loading altera_ver.dffeas

# Loading sv_std.std

# Loading altera_lnsim_ver.generic_m20k

# Loading altera_lnsim_ver.altera_lnsim_functions

# Loading altera_lnsim_ver.common_28nm_ram_block

# Loading altera_lnsim_ver.common_28nm_ram_register

# Loading altera_lnsim_ver.common_28nm_ram_pulse_generator

# Loading altera_lnsim_ver.generic_28nm_hp_mlab_cell_impl

# Loading altera_lnsim_ver.common_porta_registers

# Loading altera_lnsim_ver.common_28nm_mlab_cell_core

# Loading altera_lnsim_ver.common_28nm_mlab_cell_pulse_generator

# ** Error: (vsim-3033) data_transfer.vo(16260): Instantiation of 'stratixv_hssi_pma_tx_cgb' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# ** Error: (vsim-3033) data_transfer.vo(16391): Instantiation of 'stratixv_hssi_pma_tx_ser' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# ** Error: (vsim-3033) data_transfer.vo(16464): Instantiation of 'stratixv_hssi_pma_aux' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# ** Error: (vsim-3033) data_transfer.vo(16490): Instantiation of 'stratixv_hssi_pma_tx_buf' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# ** Error: (vsim-3033) data_transfer.vo(16577): Instantiation of 'stratixv_channel_pll' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# ** Error: (vsim-3033) data_transfer.vo(16711): Instantiation of 'stratixv_hssi_pma_cdr_refclk_select_mux' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# ** Error: (vsim-3033) data_transfer.vo(17052): Instantiation of 'stratixv_hssi_avmm_interface' failed. The design unit was not found.

# Time: 0 ps Iteration: 0 Instance: /data_transfer_vlg_vec_tst/i1 File: data_transfer.vo

# Searched libraries:

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/stratixv

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_mf

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/220model

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/sgate

# C:/intelFPGA/16.1/modelsim_ase/altera/verilog/altera_lnsim

# D:/quartus_16.1/data_transfer/simulation/qsim/work

# Error loading design

Error loading design

 

# End time: 12:02:56 on Jul 29,2020, Elapsed time: 0:00:01

# Errors: 8, Warnings: 0

 

Error.

0 Kudos

Link Copied

2 Replies
RichardTanSY_Intel
Employee
‎09-16-2020 07:44 PM
1,461 Views

Based on the errors, it seems that you might be missing some libraries or simulation models. 

You will need to check and compile the design files before running the simulation. 

 

0 Kudos
Copy link
RichardTanSY_Intel
Employee
‎10-06-2020 08:48 PM
1,427 Views
In response to RichardTanSY_Intel

Hi, 

 

We do not receive any response from you to the previous question/reply/answer that I have provided. Please post a response in the next 15 days to allow me to continue to support you. After 15 days, this thread will be transitioned to community support. The community users will be able to help you with your follow-up questions.

 

Best Regards,

Shyan Yew

In response to RichardTanSY_Intel
0 Kudos
Copy link
Reply

Community support is provided Monday to Friday. Other contact methods are available here.

Intel does not verify all solutions, including but not limited to any file transfers that may appear in this community. Accordingly, Intel disclaims all express and implied warranties, including without limitation, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement, as well as any warranty arising from course of performance, course of dealing, or usage in trade.

For more complete information about compiler optimizations, see our Optimization Notice.