close display message of EMIF IP during simulation

[lambert_yu]

Hi ,

  I have one problem how can I close the display message of EMIF IP?

  Message as follows:

      [time] [DWR=000]: Refreshing BANK_GROUP [ 0] - BANK [0]

       [time] [DWR=000]: REFRESH Command

 software : quartus 16.0

 IP : DDR4 EMIF

 Brs,

Lambert

[yoichiK_intel · Accepted solution]

If you go into the memory model you will see this kind of instantiation.

seek the "MEM_VERBOSE" and change it from 1 to 0 then memory model should stop the messages.

altera_emif_ddrx_model #(
.PROTOCOL_ENUM ("PROTOCOL_DDR4"),
.PHY_PING_PONG_EN (0),
.MEM_FORMAT_ENUM ("MEM_FORMAT_UDIMM"),
.PORT_MEM_CK_WIDTH (1),
.PORT_MEM_CK_N_WIDTH (1),
.PORT_MEM_DK_WIDTH (1),
.PORT_MEM_DK_N_WIDTH (1),
.PORT_MEM_DKA_WIDTH (1),
.PORT_MEM_DKA_N_WIDTH (1),
.PORT_MEM_DKB_WIDTH (1),
.PORT_MEM_DKB_N_WIDTH (1),
.PORT_MEM_K_WIDTH (1),
.PORT_MEM_K_N_WIDTH (1),
.PORT_MEM_A_WIDTH (17),
.PORT_MEM_BA_WIDTH (2),
.PORT_MEM_BG_WIDTH (2),
.PORT_MEM_C_WIDTH (1),
.PORT_MEM_CKE_WIDTH (1),
.PORT_MEM_CS_N_WIDTH (1),
.PORT_MEM_RM_WIDTH (1),
.PORT_MEM_ODT_WIDTH (1),
.PORT_MEM_RAS_N_WIDTH (1),
.PORT_MEM_CAS_N_WIDTH (1),
.PORT_MEM_WE_N_WIDTH (1),
.PORT_MEM_RESET_N_WIDTH (1),
.PORT_MEM_ACT_N_WIDTH (1),
.PORT_MEM_PAR_WIDTH (1),
.PORT_MEM_CA_WIDTH (1),
.PORT_MEM_REF_N_WIDTH (1),
.PORT_MEM_WPS_N_WIDTH (1),
.PORT_MEM_RPS_N_WIDTH (1),
.PORT_MEM_DOFF_N_WIDTH (1),
.PORT_MEM_LDA_N_WIDTH (1),
.PORT_MEM_LDB_N_WIDTH (1),
.PORT_MEM_RWA_N_WIDTH (1),
.PORT_MEM_RWB_N_WIDTH (1),
.PORT_MEM_LBK0_N_WIDTH (1),
.PORT_MEM_LBK1_N_WIDTH (1),
.PORT_MEM_CFG_N_WIDTH (1),
.PORT_MEM_AP_WIDTH (1),
.PORT_MEM_AINV_WIDTH (1),
.PORT_MEM_DM_WIDTH (1),
.PORT_MEM_BWS_N_WIDTH (1),
.PORT_MEM_D_WIDTH (1),
.PORT_MEM_DQ_WIDTH (8),
.PORT_MEM_DBI_N_WIDTH (1),
.PORT_MEM_DQA_WIDTH (1),
.PORT_MEM_DQB_WIDTH (1),
.PORT_MEM_DINVA_WIDTH (1),
.PORT_MEM_DINVB_WIDTH (1),
.PORT_MEM_Q_WIDTH (1),
.PORT_MEM_DQS_WIDTH (1),
.PORT_MEM_DQS_N_WIDTH (1),
.PORT_MEM_QK_WIDTH (1),
.PORT_MEM_QK_N_WIDTH (1),
.PORT_MEM_QKA_WIDTH (1),
.PORT_MEM_QKA_N_WIDTH (1),
.PORT_MEM_QKB_WIDTH (1),
.PORT_MEM_QKB_N_WIDTH (1),
.PORT_MEM_CQ_WIDTH (1),
.PORT_MEM_CQ_N_WIDTH (1),
.PORT_MEM_ALERT_N_WIDTH (1),
.PORT_MEM_PE_N_WIDTH (1),
.MEM_DISCRETE_CS_WIDTH (1),
.MEM_CHIP_ID_WIDTH (0),
.MEM_ROW_ADDR_WIDTH (15),
.MEM_COL_ADDR_WIDTH (10),
.MEM_TRTP (9),
.MEM_TRCD (18),
.MEM_RANKS_PER_DIMM (1),
.MEM_NUM_OF_DIMMS (1),
.MEM_DM_EN (1),
.MEM_DISCRETE_MIRROR_ADDRESSING_EN (0),
.MEM_MIRROR_ADDRESSING_EN (1),
.MEM_INIT_MRS0 (0),
.MEM_INIT_MRS1 (0),
.MEM_INIT_MRS2 (0),
.MEM_INIT_MRS3 (0),
.MEM_VERBOSE (1),
.MEM_CFG_GEN_SBE (0),
.MEM_CFG_GEN_DBE (0)

[lambert_yu]

Hi，

    Thanks for your help.

Brs,

Lambert