MAX10 UART RSU EXAMPLE NOT WORKING

[SAB4887]

Hello ,

I have MAX10 development kit. I am trying to play with MAX10 RSU with  UART NIOS example files according to AN741 document.

I am able to program all files correctly but when i connect UART to terminal i don't see any  compunction there.

Any idea what i am missing ???

Thanks

[SAB4887]

[Ash_R_Intel]

Hi,

Are you running as per the steps in AN741, section 1.6.2? https://www.intel.com/content/www/us/en/docs/programmable/683661/current/the-nios-ii-eds-software-application-design.html

Regards

[SAB4887]

Hello,

Yes. I am following AN741. 

And I am directly programming MAX10 with files provided by Intel. 

Do i need to setup anything specifically if i use those output files ?

[Ash_R_Intel]

Hi,

Please check your connection to the board UART port. Are you able to use the Remote Terminal.exe?

Regards

[SAB4887]

Hello,

I checked UART connection it working  fine.

Yes, i am able to use Remote Terminal.exe but i  am not seeing any data on it?

I tried on two development board both behaves same..

[Ash_R_Intel]

Hi,

Can you please tell the steps that you followed in detail?

Regards

[Ash_R_Intel]

Hi,

Any comment? Waiting for your reply.

Regards

[SAB4887]

Following steps i am following to test "UART Remote upgrade"

Step 1 :  Programmed board with  "pfl.sof" file

Step2 :  Programmed QSPI with ".Hex" file

Step 3 :  Programmed FPGA with "factory_application1.pof"

Step 4 :  the CONFIG_SEL pin on the board is set to 0

Step 5 : UART communication : FPAGA connected through J11 UART connector

Step 6 : Open "Remote terminal.exe" file & configured UART communication.

Step 7: Press the nCONFIG button on the development kit or key-in 1 in the Send text box,then hit
Enter.

But after step7 I don't see any data on Terminal window.. ????

Am I missing anything ????

Thanks

[Ash_R_Intel]

Hi,

Please check if the USB port is getting identified on your machine through Device Manager, when you plug in the connector to on-board UART and connect to your PC. If not, please install the driver.

Regards

[SAB4887]

 Yes, it is being identified as COM Port 9 when i connect to USB to J11 connector.

[hareesh]

Hi Subodh Bansode,

Are you still facing this issue?

[SAB4887]

Yes.

[hareesh]

Hi,

i am giving video link of Remote System Upgrade in Intel® MAX® 10 Devices. pls follow step by step. if you are facing issue after that let me know.

https://www.youtube.com/watch?v=KPWOpYQD_JM

Thank you,

[braind1]

This is a private video. Can you make it public?

[SAB4887]

Hello,

I did follow that video but still i am seeing same result. 

[SAB4887]

Did i miss any, above explain steps i am following ?

[hareesh]

Hi,

I am sharing example project. once again try it same steps with this project files.

https://www.intel.com/content/www/us/en/design-example/714833/max-10-max10-remote-system-upgrade-rsu-over-uart-for-nios-ii-processor.html

Thanks,

[hareesh]

Hi,

We do not receive any response from you to the previous question/reply/answer that I have provided. This thread will be transitioned to community support. If you have a new question, feel free to open a new thread to get the support from Intel experts. Otherwise, the community users will continue to help you on this thread.

Thank you.

Best Regards,

[SAB4887]

Sorry for late reply.

I did try that example project from above link. But still i am seeing same issue.

[EP1]

Hi,

I am having the same problem.

Any new information about how to solve it?

Thanks